Question about 2000 Chrysler Town & Country

1 Answer

My 2000 Chrysler town and country at 50mph the steering will shake.

Posted by on

  • Joe Vinton May 03, 2014

    At the time of checking wheels and balance also check the tire for a internal belt issue,you can balance all you want but if there is a tire problem the shake will always be there

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check wheels for balance and check wheel bearings for wear

Posted on Jan 11, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 76 Answers

SOURCE: 2002 Chrysler Town and Country

Ok, i'm assuming your replacing them, there is an oval rubber stopper on the backside of the rotor, in the backing plate, located near the bottom. it will tighten or loosen the e-brake shoes inside the rotor, loosen them all the way off, then get a big hammer and give them a really good smack, be carefull not to damage the wheel studs, if your reusing them hit on the hat of the rotor, if replacing you can hit right on the rotor face.
Use some antiseize on the hub before installin your new rotors, and don't forget to readjust your
e-brake and reinstall the rubber plug

Posted on Nov 18, 2008

keemo68
  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

c17hydro
  • 2984 Answers

SOURCE: Front PCV Valve on chrysler town and country

1930013.gif
PCV valve location-2.4L engine

3a8cecf.gif
PCV valve location-3.3L and 3.8L engines

Posted on Nov 13, 2009

  • 149 Answers

SOURCE: 2008 Chrysler Town & Country

Nope no recall on brakes

Posted on Jan 24, 2010

  • 149 Answers

SOURCE: Trouble codes on a 2000 Chrysler town and country

0775 is Presure Control Solenoid "B", 0784 is 4-5 Shift these are trans codes from the transmission Solenoid. This is a changable part for any mech. Part is around $200 & includes the gasket.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 chrysler town and country shakes and looses steering


Might be a tie rod that is what my intrepid did and it was a tie rod

Sep 23, 2015 | Chrysler Town & Country Cars & Trucks

1 Answer

Why does my 2001 Chrysler town and country shake like it has a flat tire going on a highway but does not ?


several possibilities but most likely:
1. alignment
2. bubble in tire
3. steering damper
4. wheel bearings

all worth having a knowledgeable person check it for you

Aug 26, 2015 | 2001 Chrysler Town & Country

1 Answer

When speeds of 50mph or more reached,it shakes an shimmys terrible


That sounds like a serious problem as in it should not be driven! It's hard without more information but it should be taken in and put on a hoist so all the front-end components can be checked. I've seen cars where one tire that was very low on air would cause that. But, I've also seen vehicles with broken frames, or components that were so worn out they they actually fell off going across a parking lot. Sorry, but I can't be more specific.
Good luck!
Ed

Nov 05, 2013 | 2000 Chrysler 300M

1 Answer

My 2005 Chrysler Town and Country has a shimmy when accelerating to highway speed. The steering wheel shakes, and when you let off of the accelerating it still has a perceptible vibration. Any idea of...


Start with a tire inspection, then have them balanced and rotated.

You could have worn tie rod ends as well. Most places provide a free front end inspections, but make them show you if parts are loose. If they won't show you go somewhere else.

Nov 27, 2010 | 2005 Chrysler Town & Country

2 Answers

I have a 2000 Chrysler town and country. The steering wheel locked, and the key won't turn in the ignition. I have tried everything from jiggling the wheel and the key, to rocking the van back and forth....


I have a 2000 town and country and 10 month ago we had the same problem .you have to go to the dealer and change an ignition key lock switch.i think the part was about $100. and the labor (at my mechanic) $40.hope it was helpful

Sep 27, 2010 | 2000 Chrysler Town & Country

1 Answer

Power steering belt diagram needed


Below is the diagram you requested. The drive belt also drives the power steering pump.
5bdff5c.gif

Oct 30, 2009 | 2000 Chrysler Town & Country

1 Answer

2005 Town and Country shakes. The steering wheel visibly moves back and forth when it is driven. I've already tried a front end alignment and that didn't help at all.


the steering collapsible joints have collapsed! remove the steering column and see it for your self! have it 1.changed or 2.welded that is if u dont have cash to buy a new steering column assembly.

Jun 18, 2009 | 2005 Chrysler Town & Country

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...