Question about Mazda MAZDA3

Open Question

2004 mazda 3 evap purge valve solenoid - MAZDA3 Mazda Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

Ad
savdragon
  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

  • 104 Answers

SOURCE: I have a 2004 Avalanche, 49K mileage, code PO446,

That is an EVAP code. its a vent control code. you can manually test it by powering it up if you know where its at. i cant remember exaclty where its at off the top of my head but its only 2 wires. using a volt meter you want to make sure power is getting to it, but you cannot activate it without dealer scan tool.hmmm if you can figure out which is ground and power when you give it 12 volts it should click. meaning your vent solenoid works and you have wiring problems or its leaking.

EVAP problems are hard to finde with out scanners. you can change the vent solenoid and hope it fixes it. but a code points you to the direction of a problem. hopefull its not wiring problems. in the northern states with snow. ice can pull out wires and also get clogged in the vent solenoid and lock it up. its either wiring or bad or a leaking solenoid. check condition of wires. if they look good try a vent soleniod.

if that doesnt fix it after a engine light reset and 2 weeks or so. then goto dealer. you need to reset it after repair. light will not go off on its own.GOOD LUCK

Michael
ASE certified.
plz rate

Posted on Apr 29, 2009

longbow243
  • 103 Answers

SOURCE: 2007 SILVERADO V6 EVAP PURGE SOLENOID

The evap purge solenoid is located on the intake manifold. The evap vent valve is located on the side of the fuel tank. If you have a P0449 or P0452 (I think) DTC, it will be the one on the tank that you need to replace.

Posted on Sep 01, 2009

csmock132
  • 4669 Answers

SOURCE: getting an error code of PO449 for a check engine

You are right. You need the vent valve not the purge valve. The vent valve is a dealer item. Also this is a common problem and GM has released a bulletin on this that involves moving the location of the valve and running some new lines. It comes as a kit from GM, and it costs about a 100 bucks.

Posted on Dec 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the purge valve on 2006 Yukon Denali


Replacing Vent Valve Solenoid Purge Valve Solenoid EVAP Valve 2005 GMC...

Remove the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement . Remove the evaporative emission (EVAP) line from the canister purge solenoid, perform the following:
2.1.
Push the large size white retainer portion in.


2.2.
Push down, while pulling up slightly in order the disengage the tube.


Disconnect the EVAP canister purge solenoid electrical connector (1).
Remove the EVAP canister purge solenoid bolt (2). Remove the EVAP canister purge solenoid (3) and insulator (1).

Sep 19, 2015 | Cars & Trucks

1 Answer

I have a 1999 oldsmobile aurora, northstar motor. I was told I need to replace my purge valve solenoid. Can someone please tell me where it is located?


It's under the plastic cover on top of the engine . Remove the intake manifold top cover.
Remove the solenoid quick-connect hose (3) at the EVAP canister purge solenoid (4). Remove the solenoid quick-connect hose (7) from the EVAP canister purge solenoid (4) to the enhanced EVAP service port (8). Remove the electrical connector (6) at the EVAP canister purge solenoid. Remove the EVAP canister purge (2) solenoid valve bolt. Remove the EVAP canister purge solenoid tab from the bracket (5).

Aug 06, 2015 | 1999 Oldsmobile Aurora

1 Answer

I have a truck that popped up a P0443 code up and I've been trying to see what it is so I can get it fixed thank yo


P0443 - Evaporative Emission Control System Purge Control Valve Circuit Malfunction

Possible causes: - Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection

When is the code detected? An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description: The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

P0443 Information for specific makes: P0443 ACURA
P0443 CHRYSLER
P0443 DODGE
P0443 FORD
P0443 HONDA
P0443 INFINITI
P0443 ISUZU
P0443 JEEP
P0443 KIA
P0443 LAND-ROVER
P0443 LEXUS
P0443 MAZDA
P0443 MERCEDES-BENZ
P0443 MITSUBISHI
P0443 NISSAN
P0443 TOYOTA
P0443 Evaporative Emission Control System Purge Control Valve Circuit...

Jun 03, 2015 | Cars & Trucks

1 Answer

Purge solenoid location 2008 torent


Evaporative Emission Canister Purge Solenoid Valve Replacement
Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Disconnect the engine wiring harness electrical connector (4) from the evaporative emission (EVAP) purge solenoid.
Remove the oil fill cap. Lift upward and remove cover from ball studs.
The purge solenoid is under the plastic cover on top of the engine .
Disconnect the EVAP pipe quick connect fitting (1) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the EVAP pipe quick connect fitting (2) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service. Remove the EVAP purge solenoid bracket bolt (3). Remove the EVAP purge solenoid.

the purge

Sep 20, 2014 | 2008 Pontiac Torrent

2 Answers

How to repair engine code po442 2009 mazda 5?


Check the purge solenoid under the hood common problem in mazda 5 6 cx7.

Jul 11, 2014 | Mazda Cars & Trucks

1 Answer

Need to know where to find the canister purge valve


For the location of canister purge valve,check the following help links mentioned below:--
Click the link :---

Location for EVAP Purge Valve Solenoid?

http://schematicsdiagram.blogspot.in/2012/06/2002-nissandatsun-pathfinder-location.html


------------------

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

-------------

2004 Chrysler PT Cruiser: Location of EVAP Purge Solenoid Valve?

http://schematicsdiagram.blogspot.in/2012/06/2004chrysler-pt-cruiser-location-of.html

-----------
These will help.
Thanks.

Jan 08, 2013 | Cars & Trucks

1 Answer

P0496 code


Hi there:
DTC P0496 - EVAP (evaporative emission) Flow During A Non-Purge Condition


The P0496 DTC code is a generic code which applies to all vehicle makes. A quick search on the 'net shows that this code seems to be more common with GM (Chevy, Pontiac, etc.) vehicles. In Acura, Honda, Hyundai, Kia, and Mazda vehicles, this code is described "EVAP system high purge flow" which is the same thing.


This DTC checks for undesired intake vacuum flow to the EVAP system. The control module seals the EVAP system by commanding the EVAP canister purge solenoid valve OFF and the EVAP canister vent solenoid valve ON. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system

If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this code is set and the MIL (malfunction indicator lamp) is illuminated.



Symptoms of a P0496 DTC will include MIL illumination, and most likely no other noticeable symptoms. Some may experience a hard start / crank condition. In some cases the engine may run rich which may not detected, but can cause damage long-term (think: catalytic converter damage).

Potential causes of a P0496 EVAP code include:

  • Faulty purge or vent solenod/valve
  • Plugged EVAP canister
  • Failed EVAP / fuel pressure sensor
  • Poor electrical connection
  • Short electrical circuit condition
  • (Hyundai, Isuzu)
  • Faulty canister purge valve
  • Blocked vapor canister
  • Faulty vent solenoid
  • Leaking EVAP system hose (Hyundai)
  • Faulty purge flow sensor (Kia, Mazda)

Possible Solutions

The most common fix for this DTC is to replace the purge solenoid valve. However, be sure to do a proper diagnosis before replacing parts!

Ideally you would use an advanced scan tool, with the ignition on and engine off, you seal the EVAP system using the Seal/Purge function. Then, watch the fuel tank pressure sensor reading when you turn the purge off. If the pressure value is higher than the normal range set by the manufacturer, replace the EVAP canister purge solenoid valve. Refer to a model-specific repair guide for the proper specification.


If you don't have access to the scan tool, you could always disconnect the vacuum line at the purge valve going back to the charcoal canister. Unplug the electrical connector on the purge valve, start the engine, then put your finger on the valve where you disconnected the line. If you can feel vacuum there, the purge solenoid valve is faulty and needs to be replaced. Alternately, you could simply remove the purge solenoid valve and blow into it. It is normally closed, so if air goes through then you need to replace it.


If the purge valve checks out good, either the problem with the valve is intermittent or there is a problem with the fuel tank pressure sensor. To test the fuel tank pressure sensor you will need to have a high end scan tool to monitor the tank pressure with the gas cap removed. If the sensor shows vacuum with the gas cap removed, there is a problem with the fuel tank pressure sensor.


Here is a picture of one purge solenoid valve. Yours may look similar or different, consult a factory service guide or your local vehicle dealership for more details.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | Cars & Trucks

1 Answer

Need instructions on how to replace purge solenoid valve on a mazda rx8


You don't need instructions You need an EVAP Diagram
for your vehicle Try a repair shop with a data base

Jun 06, 2012 | 2004 Mazda RX-8

1 Answer

I have a 2006 Mazda 5...evap leak...codeP0455...where do I look?


Check the EVAP canister purge solenoid valve for being stuck open. Try to blow through it by mouth. It should be closed and should not be able to blow through it by mouth with it de-energized. Can test it per TSB # 01-025/05. Potential Causes: EVAP Canister Purge Control Solenoid Valve


There is a TSB for these and other possible trouble codes to be set due to a stuck open EVAP canister purge solenoid valve - TSB # 01-025/05. A stuck open EVAP canister purge solenoid valve will also allow fuel vapors from the fuel tank to enter the engine when the fuel tank is being filled - resulting in a hard start condition. The EVAP canister purge solenoid valve is under the hood on the drivers rear of the intake manifold area

Jul 20, 2009 | Mazda MAZDA5 Cars & Trucks

2 Answers

Code 2187 of mazda 3 2004


2187 is a lean condition. It means the fuel system is sucking air from somewhere. If it's a 4 cylinder, it has a bad PCV hose which is located beneath the intake. This is a three-hour job.

May 03, 2009 | 2005 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...