Question about Cars & Trucks

1 Answer

Reset my centurion gate motor but when i push test button the gate stops half way

Posted by on

  • Centurion Systems Jan 11, 2013

    Hi there. When you reset the gate motor, did you remember to push the test button at the end of the procedure to confirm the travel limits? Did it complete the setup without a hitch, stopping in the pedestrian position? It might be helpful to check whether the status LED is flashing as this will give you an indication of what the problem could be. If you'd like to provide your number, I can get a support technician to give you a call and run through some diagnostic procedures with you.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 3 Answers

Hi there. When you reset the gate motor, did you remember to push the test button at the end of the procedure to confirm the travel limits? Did it complete the setup without a hitch, stopping in the pedestrian position? It might be helpful to check whether the status LED is flashing as this will give you an indication of what the problem could be. If you'd like to provide your number, I can get a support technician to give you a call and run through some diagnostic procedures with you.

Posted on Jan 11, 2013

  • Yacoob latib
    Yacoob latib Nov 13, 2013

    Hi my d2 motor won't run it beeps 4 times when triggered

  • Centurion Systems Nov 14, 2013

    Hi there. The fact that it beeps four times seems to indicate that it is encountering an obstruction, or has encountered that maximum number of allowable collisions. Have you checked for dirt or debris on the track? You can also try removing and reapplying power and then checking whether the motor operates - this will clear the collision counter. Perhaps it would be best if I got a technician to phone you when you are at the motor. Do you perhaps have a contact number for me?

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 77499 Answers

SOURCE: How to programme a digikey 4 button remote on a centurion d3 gate motor

You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Posted on Oct 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Lift gate will not power down to closed when button on gate or remote is pushed. Lights do flash though.


There are switches on both ends of the course of the motor, if one fails it will only work on the side that´s ok. That´s why it opens but do not close.Check it out.

Oct 24, 2015 | Cars & Trucks

1 Answer

Sliding gate suddenly inoperative, centurian d3 motor, test button flashes 5 times when pressed


Some motors have a thermal (red) reset button on the back of the motor that needs to be reset . And if you haven't yet try turning off the power breaker for a sec then test it again.

Oct 25, 2013 | Cars & Trucks

1 Answer

Trouble shooting Centurion D10 gate motor


look for a loose wire and faulty earth check for wires shorting out to earth

Jul 14, 2013 | Cars & Trucks

1 Answer

My Centurion D5 will intermittently reopen the gate immediately after I close it. The LED lights flash 4 times which I believe indicates an obtruction but there is no obstruction. Any thoughts as to w


Hi there. The symptoms you describe as well as the error indication (4 flashes) certainly do seem to indicate an obstruction. Try disengaging the gate, moving it back and fourth and feeling whether it sticks at any particular point. Possible causes could be: dirt or stones on the rail, bad rack joints, missing teeth in the rack, worn wheels or guide-rollers or a damaged rail. You can also try decreasing the collision sensitivity (I can send you an email with the info if you like), but please be advised that this makes the gate less sensitive to an obstruction and could pose a risk. How old is the motor, if I may ask?

Nov 27, 2012 | Cars & Trucks

1 Answer

How to programme a digikey 4 button remote on a centurion d3 gate motor


You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Oct 08, 2012 | Cars & Trucks

3 Answers

The rear lift gate on my 2006 Lincoln Navigator will not open automatically or manually and there appears to be no way to access anything inside the door from inside or out.


POWER LIFT-GATE OPERATION - To open the optional power liftgate, push the button on the instrument panel , press on your five-button key fob (if equipped), or press and release the control located in the left rear quarter panel (Figure B). To unlatch the liftgate glass, push the button ) under the center of the license plate lamp shield, or press on your five-button key fob. Do not open the liftgate or the liftgate glass in a garage or other enclosed area with a low ceiling. Keep clear of the liftgate when operating the rear switch. To open the liftgate manually, pull the handle located on the liftgate to release the liftgate from the vehicle. The power system will take over when you release the handle. To close, make certain the rear window is closed, and then pull down the liftgate a few inches to activate power closing. Closing the gate rapidly or more than a few inches may activate the obstacle detection feature and stop the power system.------------ Also click this link for more help:--- http://technoanswers.blogspot.com/2011/05/power-liftgate-on-will-not-open-on.html ------------ This should help.Keep updated.Thanks.Helpmech.

May 19, 2011 | Lincoln Navigator Cars & Trucks

2 Answers

Rear Windshield Wiper Motor


look closely/carefully for recessed screws. Most are usually pop on/ pop off types. Pull/ pry gently.

Jul 17, 2009 | 1998 GMC Jimmy

2 Answers

Rear window won't go up and down


thats easy,spray the switch at the latch on the drivers side,and open and close it a few times,that switch keeps the window from going up with the gate down and they do get sticky

Apr 13, 2009 | 1991 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...