Question about 2004 Volvo S60

1 Answer

Clearing service message on dash

How do you clear the message on the display

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Turn the ignition to position 1 Push and hold trip reset while holding. Turn to position 2 hold trip reset till the service light flashes 3 times and then release. You should hear a beep to let you know it is reset. It might take you 2 times sometimes. If you have the message in the text window the little triangle in the center of the speedo assy. will flash. Also another trick to help you is when the milage returns the light should be reset.

Posted on Jan 22, 2009

  • blueextc3221
    blueextc3221 Jan 22, 2009

    Additionally....

    Here it is for all you guys who are proud Volvo owners s60 years 01-03 maybe newer cars too.

    Resetting the Service reminder indicator (SRI), model years -2001
    The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The lamp remains lit for 120 seconds when the ignition is switched on.
    Note! If the lamp flashes, it may be because one of the service parameters has not been programmed.
    Proceed as follows to reset the service reminder indicator (SRI):
    -Ignition position I
    -Press and hold in the reset button for the trip odometer
    -Ignition position II
    -The service reminder indicator (SRI) starts flashing when the reset button for the trip odometer has been pressed for 10 seconds
    -Release the reset button for the trip odometer within 5 seconds. The instrument gives an audible signal when resetting has succeeded.
    Note! If the trip meter reset button is not released within 5 seconds the indicator is not reset. However the indicator will stop flashing.


    Resetting the service reminder indicator (SRI), model years 2002-
    The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120 s each time the ignition is switched on.
    Proceed as follows to reset the service reminder indicator (SRI):
    -Ignition position I
    -Press and hold in the reset button for the trip odometer
    -Ignition position II.
    Note! Turn the key to position II within 2 seconds.
    -Hold the reset button for the trip meter pressed in until the original value has been reset.
    Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released.
    -Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded
    -If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds.
    Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.

    Thank you for using FixYa! A FixYa rating is appreciated!!

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I clear a service emissions message on a 2005 Mercury Mariner with a 3.0L engine. I have performed the required maintenance procedures at both 30,9000090's and 60,000miles. Still have message.


Warning Messages The warning messages can interrupt the display until cleared or reset by the driver. The warning messages are either single cycle, non-resettable, or repetitive warning messages.
The single cycle warning messages display once whenever the ignition switch is turned to the ON position or a fault occurs in a system, and can be cleared by pressing the RESET button. The single cycle warning messages are:
  • liftgate ajar
  • liftgate glass ajar
  • service emission system
  • low brake fluid
  • service brake system
  • check left headlamp
  • check right headlamp
  • check left turn lamps
  • check right turn lamps
  • check left high beam
  • check right high beam
  • check brake lamps
  • check parking lamps
  • washer fluid low
  • check fuel cap
  • change oil soon
  • change oil now
  • low fuel
  • service 4x4
  • turn signal on

Jun 15, 2016 | Mercury Cars & Trucks

Tip

SAAB service light 900


900

All Years

To clear "TIME FOR SERVICE" from the Saab Information Display, press and hold the "CLEAR" button for at least 8 seconds. A signal will be heard indicating reset. After the 21st restart of the vehicle, the "TIME FOR SERVICE" message will be cancelled.

on Dec 07, 2009 | Saab 900 Cars & Trucks

Tip

Audi service light (all)


To reset the OIL message on the speedometer display, turn off the ignition. Press and hold the button on the left side of the display while turning the ignition on. Service OIL will be displayed. Pull out the button on the right side of the display until the service prompt is cleared. The display should now read ---.
If this procedure does not work, follow this procedure: With the ignition off, push the right button. Turn the ignition on and then pull the left button. This should clear the warning message.

on Dec 07, 2009 | Audi A4 Cars & Trucks

1 Answer

How do i reset the sid display in 2008saab93turbo after replacing battery


pressing the CLEAR button for 8 seconds. on older 9-5 and 9-3 SID's, that you must press CLEAR once & release, then press CLEAR a second time, and hold for 8 seconds. While holding down CLEAR for this second time period, at the 4 second mark "CLEARED" will be displayed, and you will hear 1 beep. If you release the CLEAR button at this point, the DTE and MPG will be cleared out. If you continue holding the CLEAR button past the 4 and 8 second marks, you will hear a 2nd beep, and "SERVICE" will be displayed. This now means that you have cleared and reset the Time For Service message.

Dec 01, 2014 | 2008 Saab 9-3

1 Answer

Codes to clear service messages on Renault grand scenic 2007


press the button on end of wiper stalk, until you reach service intrvil on dash, then press and hold trip counter switch , this willl move to next service milage done,

Feb 09, 2013 | 2000 Renault 181

2 Answers

Hi, how do i put off ''maintenance required'' sign on my toyota camry 2007 car dashboard?Just did the servicing, the sign is still there?


with the key in the off position press and hold the odometer trip reset button on the dash. Turn the key to the run position while continueing to hold the reset button, do not start the car. The odemeter display should change to all dashes and then the dashes will start to go off one at a time. Once they are all out the odometer will display all zeros and then return to its normal display. Sometimes the trip A odometer needs to be displayed before starting and sometimes the trip B.

Your owners manual will give you some more insight if needed.

Sep 29, 2010 | 2007 Toyota Camry

1 Answer

Como quitar en la pantalla SERVICE


To reset the OIL message on the speedometer display, turn off the ignition. Press and hold the button on the left side of the display while turning the ignition on. Service OIL will be displayed. Pull out the button on the right side of the display until the service prompt is cleared. The display should now read ---.
If this procedure does not work, follow this procedure: With the ignition off, push the right button. Turn the ignition on and then pull the left button. This should clear the warning message.

Hope helps (recuerde calificar esto).

Sep 22, 2010 | 1999 Audi A6

2 Answers

Reset oil change light on my 2004 Audi 1.8T


  1. Turn off the ignition
  2. Press and hold the button on the left side of the display while turning the ignition on
  3. Service OIL will be displayed
  4. Pull out the button on the right side of the display until the service prompt is cleared
  5. The display should now read ---
  6. If the above procedure does not work, outlined below is an alternative procedure:
  7. With the ignition off, push the right button
  8. Turn the ignition on and then pull the left button
  9. This should clear the warning message --- I have a 2002 A4 Quattro. To reset that Service message, hold down the service button. That's the one with the picture of a wrench on it. While holding it down, turn on the ignition. Let go of the service button and press the "Mode" button just to the right of the service button. It should clear the display.
* This does not work in older models, like my Audi A4 /1.6, 1995. It needs the cable and the program ( e.g. VAG-COM). Even with this, clearing the code (IN1 or IN2) is quite complicated.

Nov 13, 2009 | 2004 Audi A4

3 Answers

Orange symbol on dash


What does the light resemble?

Sep 30, 2008 | 2003 Saab 9-3

Not finding what you are looking for?
2004 Volvo S60 Logo

Related Topics:

1,717 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...