Question about 2006 Chrysler Sebring

Open Question

2006 chrysler sebring 2.4 crankshaft position sensor location ?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Molson02536
  • 3854 Answers

SOURCE: camshaft position sensor

This V-6 has a very hard to find/hard to reach CKP - it is directly under the Distributor, about 4 inches below, inwards toward the Transaxle "bell". Almost dead-center in the back of the engine.
Your going to have to take the Air Filter and the air manifold that runs to the engine off. After that, take off the horn assembly to gain very, very limited access to wedge an extended ratchet into the bowels of the engine. 
I think the same socket that undid the horn assembly fit the CKP nut. It takes 10 minutes to undo the bolt a couple ratchet clicks at a time, at least 15 to get the thing to wiggle out, probably 15 minutes to unconnect, reconnect, and snap back to the fram the wire harness, and at least another 10 minutes to ratchet the bolt back in click by click.

Now you know why they say shops charge $500 in to do this - I think they must take the entire engine out... Very painstaking job that requires patience and precision... but quite satisfying to finish it yourself. 

Good luck and hope this helps, 

Posted on Apr 23, 2009

  • 1 Answer

SOURCE: Where is the crankshaft position sensor located?

the crankshaft position senor on the 2.2L is located on the rear right side of the engine block

Posted on Jul 07, 2009

co7196
  • 3433 Answers

SOURCE: need location of crankshaft position sensor on a

The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Posted on Sep 28, 2009

  • 1 Answer

SOURCE: 98 chrysler sebring 2.5 v 6 crankshaft sensor

Driver Side of engine, mounted below battery tray and distributor.

Posted on Feb 21, 2010

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

Posted on Apr 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does a crankshaft sensor do? what does a camshaft sensor do?


get a HAYNES repair manual, tells you what all sensors do ! the crankshaft sensor sends info to the SBEC, reguarding engine crankshaft position. the camshaft sensor reads camshaft position, sends a coded signal to the SBEC, which uses this info to determine whether the fuel injectors and ignition coils are correctly synchronized !

Feb 14, 2013 | Chrysler Sebring Cars & Trucks

1 Answer

Sebring 1997 I need picture to lookat the PCM sensor and the Crankshaft position sensor (CKP sensor)


On 1997 Chrysler Sebring 2.5L MFI 6cyl...
- the PCM is located in the left side of the engine compartment, beside the Power Distribution Center (PDC).

zjlimited_767.gif

Fig. 1: Location of the PCM on the Cirrus, Stratus, Sebring convertible and Breeze models

zjlimited_768.gif

Fig. 2: Location of the PCM on the Sebring coupe and Avenger models

- the Crankshaft Position Sensor is located: under hood, driver side, upper engine area, mounted on end of engine block

zjlimited_769.gif

Fig. 4: Location of the crankshaft position sensor on 2.5L engines

Hope helps; remember to rating this answer and leave some testimonial comments.

Oct 09, 2011 | 1997 Chrysler Sebring

1 Answer

No fire at distributor


The 1997 Chrysler Sebring 2.5L has a distributer with an intergrated coil. All other models have a distributerless ignition ("coil packs").

Start by testing the ASD (Automatic Shut Down) relay, then the CPS (Crankshaft Position Sensor) and CMH (Camshaft Position Sensor).

The CMH test the same way likethe CPS; the ASD is located on cowl, at left rear of engine compartment.

Hope helps.

Jul 28, 2010 | 1997 Chrysler Sebring

1 Answer

Where is the crankshaft position sensor located on a 2000 Sebring Conv.


removal steps (CPS) -remove air intake hose -Battery tray -Crankshaft position sensor

Apr 27, 2010 | 2000 Chrysler Sebring

1 Answer

How can i replace the crankshaft position sensor on a 1999 sebring lxi


Fig. 2: Location of the crankshaft position sensor on 2.4L engines

fabab4c.jpg

Jun 25, 2009 | 1999 Chrysler Sebring

1 Answer

Where is the crankshaft position sensor located? On a 2004 Chrysler Sebring 2.2L


the crankshaft position senor on the 2.2L is located on the rear right side of the engine block

Jun 13, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
2006 Chrysler Sebring Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...