Question about 2000 GMC Yukon

1 Answer

Power steering 2000 yukon 5.3 broke shaft in steering pump, replaced pump had steering for about a week. lost power, replaced pump again, nothing replaced gear box(pitman arm also replaced due to play in it) still no power steering. there is some sort of electric control or sensor on the pump but I dont know what it does. does anyone know what would cause this? thanks

Posted by on

  • rudy thompson
    rudy thompson Jun 04, 2012

    power steering,,the whole thing is contaminated with metal debree x contamination ,replace both steering rack and pump,,at the same time and maybe hoses.

  • rudy thompson
    rudy thompson Jun 04, 2012

    I had the same problem 2001 yukon xl ,,,power steering

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Blow that dang truck up

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering pump shaft broken again


When you place the wheel in a hard lock position ,the power steering pump relies on the pressure by-pass valve to operate instead of the valves in the steering box to open and allow the pressure to by-pass back to the reservoir.. When you hit hard lock and you hear the motor load up just ease on the turn and the pump will operate as designed. The turn will still be the same -just that the pump is not under full load . Breaking the shaft is a sign of excessive load and a misaligned pulley so check that the belt is directly in line and the pump is square to the belt line.

Mar 02, 2014 | 2004 Chevrolet Suburban

1 Answer

My 2003 ford focus lost it's power steering, mechanic replaced the rack and pinion thing - lost steering again and now the mechanic says it is the power steering pump. The rack and pinion was replaced...


if the rack and pinion was not leaking or causing problems. then he may of made a wrong move! if the rack was fine before, and you just lost power steering. then it is most likely the power steering pump or the lines that go from rack to the pump. good-day ! if a rack goes bad, you will get a bad steering problem or just bad steering.

Aug 23, 2011 | 2001 Ford Focus

1 Answer

2000 GMC Sierra 1/2 ton. Sounded like a wheel bearing might be going out. what it is just broke and you can not turn the wheel without pulling hard. Checked Steering Fluid full pump not frooze up what...


Remove your belt and see if you can pull the power steering pump pulley off by hand. I have had the shaft of the pump break before and everything looks still good and fluid level still full. Then I removed the belt and the pulley and half of the broken shaft just pulled right out of the pump. The pump could still be bad even if the level is good. Lift front off of the ground and inspect your steering components and make sure your wheels turn freely.

May 10, 2011 | 2000 GMC Sierra

1 Answer

Power steering not working tried adding power steering fluid didn't work.


The Pontiac power steering pump run off a shaft driven and not belt driven. This means that when the steering system is stressed instead of the belt slipping it puts a lot of stress on that shaft and could cause that to break. If nothing seems to effect the power steering I would have to guess that this is what happened and the power steering pump will have to be replaced.

Sep 21, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Two power stearing pumps broke replacing the third now one lasted 1yr other one lasted 3 month both shaft broke why what about hydro boost


theres a mojor problem with these pumps, the shaft fractures it was a defect build call your dealer theres a revised pump to replace these and may be under warranty. they are also paying customer back for repairs.hydro boost also uses a power steering pump, the diffrence is theres no vaccum booster in hydro boost the brakes are power with the power steering pump, next thing is try useing a dealer part and make sure the pulleys are all lined up and replace the pulley on the pump also. hope this helps.

Feb 18, 2010 | 2000 Chevrolet 3500

1 Answer

Power steering on 2000 gmc qit working


Those are Notorius for the shafts in the pump itself breaking.. Remove the serpintine belt.. then grab the pulley on the ps pump and see if it pulls out.. if it does.. Pump Time Boys-n-Girls.. Hope this helps.. Thank you

Mar 11, 2009 | 2001 GMC Yukon

1 Answer

Cranks but wont turn over


you know. i took it to a mechanic and actually.... The timing belt cut the Crank Shaft Censor... So it was the crank shaft censor again. The wires were routed wrong from the first mechanic that "fixed" the car.

Aug 01, 2008 | 2000 Hyundai Sonata

Not finding what you are looking for?
2000 GMC Yukon Logo

Related Topics:

465 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...