Question about 1993 Buick LeSabre

1 Answer

Big Problem My exhaust keeps falling down and dragging on the ground... plus my key snapped turning the car on and my driver side door doesn't close, so I had bungy cord to close it, but that snapped so now I have too hold it closed while I drive... :S what should I do?

Posted by on

  • Jyackle5
    Jyackle5 May 11, 2010

    Donate the car and buy a new one. Or if you want try to trade it in.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Use hanger wire to hold up your exhaust until you can take it to a muffler shop to have it properly welded, replace your ignition switch with a new one (you get a brand new key with it!) as for your door fiddle with unlock/lock to check if your door lock is stuck on open and doesn't let your door close all the way, make sure the latch mechanism on the door as open/down and that it hooks up with the striker on the frame of the car. Way cheaper than having to buy a new car.

Posted on Feb 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the battery in a jaguar XF smart key


1) Carefully remove the plastic silver sleeves on each side of the remote.
2) Carefully open the remote to expose the battery -- try to keep the circuit board and valet release pin from falling out.
3) Replace battery -- plus (+) side down
4) Before closing body of remote, take note of valet key release pin & spring. Be sure the spring and pin are in the correct position (see pic).
5) Carefully close body of remote.
6) Before attaching sleeves to remote body, be sure the notched end of the sleeve is aligned with the valet key.
7) Carefully slide silver sleeves onto each side
8) Test
change-battery-in-jaguar-xf-smart-key-c4xwafwrcxpjyaxsfmhtpc1n-4-0.jpg

change-battery-in-jaguar-xf-smart-key-c4xwafwrcxpjyaxsfmhtpc1n-4-2.jpg

change-battery-in-jaguar-xf-smart-key-c4xwafwrcxpjyaxsfmhtpc1n-4-5.jpg

change-battery-in-jaguar-xf-smart-key-c4xwafwrcxpjyaxsfmhtpc1n-4-9.jpg

Apr 24, 2014 | 2009 Jaguar XF

1 Answer

1993 Bighorn Passenger window not working


There could be a lock controller somewhere that is not working.
I don't have a wiring diagram for your truck.

Generally, the power window motors are grounded thru the doors, or the switches provide ground. In your case the motors are probably grounded thru the doors.
The master switch "overrides" the door switch so you have extra wires that do the same thing. The E wire probably gives the door switch power and the A and C are up and down. The B and D are override circuits from the master that bypass the door switch.
Sometimes the motor is grounded thru the switch then thru the door.

Jun 28, 2012 | Isuzu Trooper Cars & Trucks

1 Answer

"automatic" window on my 2005 mustang does not


So when it doesn't seal that means the tracks the window have been falling out typically. The door panel needs to come off to inspect the tracks. And if your driver side power window doesn't work, that typically means a seperate problem located in the switch itself. It could also be the wires, so you can run a seperate wire to test the switch by running it directly to the window motor, and pressing the switch down. This can easily be done while the door panel is off so you can hit two problems at the same time.

Oct 20, 2011 | 2005 Ford Mustang

1 Answer

Had battery replaced but radio, power locks, and trunk button doesn't work. what do i do?


DEALERSHIP HAS TO RESET RADIO BUT YOU CAN REPROGRAM DOOR LOCKS BY CLOSING ALL DOORS.INSERT IGNITION KEY IN IGNITION SWITCH.ACCESS DATA LINK CONNECTOR ON DRIVER SIDE FASCIA JUMP DLC TERMINAL 1 AND GROUND TERMINAL 1 MAY ALSO BE GROUNDED USING DIAGNOSTIC EQUIPMENT CONNECTED TO THE DLC.SWITCH IGNITION SWITCH ON AND BACK OFF POSITION ENSURE DOORS LOCK AND UNLOCK INDICATING PROGRAMMING MODE ACTIVE.PRESS ANY BUTTON OF EACH REMOTE TRANSMITTER THREE TIMES WITHIN TEN SECONDS. WAIT 1 MINUTE OR REMOVE JUMP LEAD TO EXIT PROGRAMMING MODE.

Sep 10, 2011 | 2001 Chrysler Sebring

1 Answer

Tailpipe is hanging very low


Hi. Under or near the tailpipe, there are rubber and sometimes steel hangers that are placed onto the sides of the pipe structure. These move with the assembly to provide little flexibility during travel. These hangers also are there to keep the pipe/muffler assembly from dragging or hanging to low. When the hanger assembly becomes unstable or damaged, it will allow the tail pipe assembly to hang low or sometimes drag the ground when you hit a bump. The necessary actions are to raise the vehicle high so that you can inspect the exhaust tail pipe assembly for broken hangers or steel bracing devices. replace any rubber hangers that may be snapped or missing form their respective locations. If you are uncomfortable with raising the vehicle, i would take the unit to a local muffler/exhaust shop for the inspection.

Aug 25, 2010 | 2003 GMC Yukon Denali

2 Answers

Only the drivers door lock will unlock with the keyless remote (even when clicked two times) but the other three doors remain locked. They will unlock when I manually push the unlock button on the inside...


i had the same probem,[try this] you need 2 remote keys,put 1 key in the drivers door get in the car and close the door put the other key in the ignition press and hold down the open option on the key then turn on the ignition lights [do not start] hold the button for 30 seconds turn off ignition get out of car remove door key and that should solve the problem,pete please let me know if this works]

Mar 10, 2010 | 2001 Volkswagen new Passat

1 Answer

How do I take off the door panel to replace the lock


just take a screw driver or pry bar and open the door and it ll pop off. It has clips that snap into the door to hold it on. dont let it fall to the ground or it will pull out wires for windows and door locks. set a box or something under it to keep it from falling to the ground.

Nov 03, 2009 | 1999 Ford Explorer

2 Answers

Anti theif light is blinking fast & it wouldn t


OOPS dealer only ,Try opening and closing door lock three times drivers side 10 sec interval between clicks then try starting if no go then dealer only

Mar 14, 2009 | 2000 Ford Windstar

1 Answer

Door locks


behind the lock cyl. is a snap ring if you shine a mirror up at it you will see it p.s you would want to put a rag down in the door covering up the gap when you pull the snap ring out it will fall down toward that gap if it falls in that gap it is hard to get out

Sep 05, 2008 | 2003 Honda Civic

Not finding what you are looking for?
1993 Buick LeSabre Logo

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...