Question about Cars & Trucks

Open Question

Adjust rear brakes on movano van

Hand brake adjustment

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 24 Answers

SOURCE: need to change rear pads and adjust hand brake on a 407

right the hnad brake is located on the center console at the right of you in america or left if you are are from brittan. pull it=]

Posted on Jun 26, 2008

  • 98 Answers

SOURCE: parking brake adjustment

On the accents what you need to do is to remove the plastic casing from around the parking brake mechanism. Towards the back on each side there is a screw that needs to come out. Then you will just need to wiggle the plastic casing out and around from the parking brake and set it aside with the screws. Once that is off on the inside there will be what looks like one long (gold colored) screw and at the bottom there will be a mini cable running off to each side. At the end of the tension adjuster is where you adjust it. Mine was very loose and I had to tighten it down quite a bit. It takes a 12 MM wrench. You will want to turn the wrench toward the passenger side to tighten it down. Hope this works for you.

Posted on Feb 25, 2009

  • 150 Answers

SOURCE: Disc Brake Emergency brake adjustment on 04' Chev Express Van

Continually push the brake pedal to set the brakes. (With park brake off). Brakes are self adjusting and will adjust to correct position.

Posted on Mar 29, 2009

  • 77 Answers

SOURCE: adjusting kia sedona rear brakes

I think if the self adjusters are working properly you should be able to push the parking brake pedal (e-brake) to the floor once and release pedal. .

Posted on Jan 30, 2010

  • 1 Answer

SOURCE: hand brake requires adjusting

Hi
how do i adjustthe hand break cable on my peugeot 405
thanks
P.S my e-mail mrs1342@yahoo.com

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do I fixed if my car hand brake stuck 2001 toyota coralla manual


There are several things that can make a hand brake stick on. It possible the cable attached to the leaver has come off it guide. There is a cable running from each rear wheel to the handbrake leaver , a inner cable running through a outer housing , chick that the inner cable is free to move back and forward . if all the cables are free to slide adjust the rear brakes and hand brake as instructions . Slacken off the hand brake cable adjustment. Jack up the rear wheals and adjust the brake shoes till the brakes lock, then back off till the wheels are free to turn. Then pull the hand brake leaver on two clicks and adjust the hand brake cable till the rear wheels just start to bind, release the hand brake leaver and check the wheels are free to turn.

Nov 27, 2014 | 2001 Toyota Corolla

2 Answers

How to repair rear brakes on Renault Kangoo Van


I thought Kangaroos walked on 2 legs.
ask your brake man?

FOOT main rear brakes or the rear hand emergancy brake.?
he :(both)
1: looks at them for wear and leaks.
2: Replace pads and shoes and all the parts that he SEES are bad.
3: adjusts them per FSM.
4:and road tests. it.

Jun 30, 2014 | Cars & Trucks

1 Answer

2002 town & country hand break does not work, can still drive wth the hand break on


Set & release the handbrake 10 to 20 times. This action moves the adjuster slightly each time until the brake shoes adjust to a certain distance from the drum., if this method doesn't work, your going to have to locate the adjustment on the cable itself under the van it runs along the side rail , it could be the cable has stretched and may be past the point of adjustment,, or the rear brakes are worn

Jul 10, 2011 | 2002 Chrysler Town & Country

1 Answer

1998 ford escort se hand brake need adjusting. doesn't hold.


Try to adjust the rear brakes tighter at the shoes, if you have drum brakes. May require taking the drum off and adjusting the adjuster. Or, adjusting it from the backing plate access hole if there is one.

Be sure to check the cables to make sure they are not broken anywhere between the hand brake lever and the back brakes.

Good luck on this repair.

ADJUSTMENT


  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake drum.
  4. Using a brake adjusting gauge, measure the inside diameter of the brake
    drum.
  5. Compare the brake drum measurement to the brake shoes.
  6. Adjust the brake shoes by inserting a brake adjustment tool into the knurled
    quadrant of the rear quad operating lever and adjust the shoes to the same
    measurement as the brake drum.
  7. Install the brake drum.
  8. Install the wheel and tire assembly.
  9. Lower the vehicle.
  10. Check the brake system operation by making several stops while driving
    slowly forward.


prev.gif next.gif

Nov 02, 2010 | 1998 Ford Escort

1 Answer

Hi there i drive a 1989 nissan homy 4wd van engine type TD27. my problem is the hand brake light remains on when hand brake is off and not sure what this means.I have been told it might be the brake oil...


This used to happen in my 1979 Honda if the brake cable wasn't adjusted tightly enough, either due to the cable adjustment or the rear drum brake adjustment.

If I would push the hand lever down all the way, the light would go out.

Aug 01, 2010 | Nissan Minivan Cars & Trucks

1 Answer

1999 Dodge Ram 1500 conversion van rear brake hammering


Are the brake shoes on right, there are two size shoes, One shoe has a longer brake lining then the other. The short brake lining is towards the front of the van and the longer brake lining is towards the rear. The rear brakes also may need to be adjusted, you can do that by going in revers in a empty parking lot and push the brakes as hard as you can to stop the van. Don't give your self a whip lash, just push down gradually and as far to the floor you can about 7 to 10 times. The self adjusters should adjust the brake on both sides, try this first before you take the brakes apart again. It may just need a adjustment and after that check the brake fluid in the master cylinder. Good luck and hope this helps. Keep me posted, be glad to help

Jun 20, 2009 | 1999 Dodge Ram

1 Answer

Adjust rear brakes Hiace van


usually this vehicle is equipped with rear drum brakes with auto adjuster. thy backing up about 30 kph and step on the brakes hard. do this 2 or 3 times this should adjust the brakes.

May 28, 2009 | 1991 Toyota Pickup

2 Answers

Disc Brake Emergency brake adjustment on 04' Chev Express Van


Continually push the brake pedal to set the brakes. (With park brake off). Brakes are self adjusting and will adjust to correct position.

Mar 29, 2009 | 2004 Chevrolet Express

1 Answer

Rear brakes scrubbing on 1998 chevy venture van


Removal Procedure Tools RequiredJ 38400
Caution: Keep fingers away from rear brake shoe springs to prevent fingers from being pinched between spring and shoe web or spring and backing plate.
  1. Remove the brake drum. Refer to Brake Drum Replacement

  2. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  3. Use the J 38400 in order remove the adjuster spring (1). Disengage the adjuster spring loop from the tab on the adjuster actuator.
  4. 2.1. Remove the loop end of the adjuster spring from the adjuster actuator. 2.2. Remove the straight end of the adjuster spring from the secondary brake shoe.
    142293.gif
    tif.gif
  5. Use the J 38400 in order to spread the brake shoes apart.
  6. Remove the adjuster.
Installation Procedure

    142293.gif
    tif.gif
  1. Use the J 38400 in order to spread the brake shoes apart.

  2. 178990.gif
    tif.gif
    Important: Ensure that the adjuster (2) engages the brake shoes (4 and 5), the park brake actuator (3), and the adjuster actuator (1) properly.
  3. Install the adjuster.

  4. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  5. Install the adjuster spring (1).
  6. 3.1. Install the straight end of the adjuster spring into the secondary brake shoe. 3.2. Install the loop end of the adjuster spring to the adjuster actuator.
  7. Install the brake drum.

Dec 06, 2008 | 1999 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...