Question about 2002 Jeep Liberty

1 Answer

How to take off the bolt in front driver seat belt on the side?

Please help with any info on how to take off the bolt of the front driver seat from the seat belt that is bolted on the side?

You need a T50 torque bit.

It broke 2 of my rachet set adaptors and I tried with the drill, but it's hard as a rock... It won't even turn with all the drill torque...

Please help!!!!

Posted by on

  • eugene bae Jan 22, 2009

    Thank you Sooner!!!

    Can you please tell my why it's not working with a drill?

    Is it really that bad or it's just this one?

    Also, a screw driver shouldn't work since it's a T50 torque bit, isn't that correct?

    Thanks again sooner!!!

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

I have always had good luck with a Large Screw Driver and a Oil Filter Wrench Believe it or Not!

Posted on Jan 22, 2009

  • Travis Humphries
    Travis Humphries Jan 22, 2009

    No Problem Bro! That's why I am here! I am too Tight to Purchase the Heads Required so, I just get a Screw Driver that will fit Snug into the Star and Torqe the HELL out of it!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the original seat covers from a PT Cruiser driver seat


get under the front seats there are 4 bolts holding the seats in the floor plus a torx bolt for the lap belt, take seats out the back seat has 2 torx bolts at the front bottom of the lower cushion remove them and pull the bottom forward the back has 2 bolts holding it remove them and lift the unit straight up, be carefull there is wires under the front seat for the seat belt warning light carefully unhook them 1 for each seat now you need hog ring plairs and a bunch of new hog rings to secure the new fabric, use side cutter plairs to remove old hog rings carefully remove the seat covers, hog rings can be got at car glass shops the pliars can be got from summit racing or a place that sells car uppolstrytake your time and you can do it!!

Oct 29, 2014 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Remove seat belt


Hi Ray, Removal of the seat belts requires removal of the seats. Adjust the front seats to the fully backwards position and remove the fixing bolts and then unhook rails at the rear.You will notice a wire cable attached to each seat used to adjust the belt shoulder hight. This must also be disconnected. On later model vehicles there is an automatic retraction unit which pulls the driver and or passenger back into the seat in the event of the air bags being deployed. These connections must also be removed. If seats are electrically operated unplug all connectors. Remove seats and then gently remove plastic door pillar covers. (These are in two pieces for each front belt.) Removal will leave the fixing bolts of retractable part of the seat belt exposed. The buckle side is fixed with one bolt and has an electrical connection which must be disconnected. Hope this is of help? Regards John

Oct 27, 2013 | BMW Z4 Cars & Trucks

1 Answer

How does the trim remove to change out front seat seat belts in 2001 beetle


this case first remove cove from up side of seat belt it's look like around side up.from down side of this cover there is tow small lock with screw driver pull this side out then push up . then you can see bolt (19mm) remove , then down big cover (difrent coler) .remove tow door step cover have littile hard lock remove with screw drive it may be 3 or 4 lock for each one ,then the middle cover for seat belt have .

Aug 03, 2011 | 2001 Volkswagen Beetle

2 Answers

Hi, I would like to know if the front seat belt retractors for Honda CRV 2003 are the same? If yes, is it difficult to replace the seat belt assembly? I'm planning to buy a used front passenger side...


I don't know if this is something you want to get into? You decide. Front Seat Belt Replacement SRS components are located in this area. Review the SRS component locations and the precautions and procedures before performing repairs or service.
NOTE: Check the front seat belts for damage, and replace them if necessary.

Front Seat Belt

  1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
  2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
  3. Slide the front seat forward fully.
  1. Pull the lower anchor cover (A) back, and remove the lower anchor bolt (B).
  2. Remove the B-pillar lower trim panel.

  1. Remove the upper anchor cover (A), and remove the upper anchor bolt (B).

  1. Disconnect the seat belt tensioner connector (A), and detach the harness clip (B) from the retractor (C). Remove the upper retractor mounting bolt (D), and the lower retractor bolt (E), then remove the front seat belt (F) and retractor.
  2. If necessary, remove the front seat belt protector (G).
  3. Remove the B-pillar upper trim.

  1. Remove the shoulder anchor adjuster (A).

  1. Install the seat belt in the reverse order of removal, and note these items:
    • Assemble the washers, collar, and bushing on the upper and lower anchor bolts as shown.
    • Check that the retractor locking mechanism functions.
    • Apply liquid thread lock to the anchor bolts before reinstallation.
    • If the seat belt tensioner has been activated, replace the front seat belt protector with a new one.
    • Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.
    • Make sure the seat belt tensioner connector is plugged in properly.
    • Reconnect the negative cable to the battery.
    • Enter the anti-theft code for the radio, and then enter the customer's radio station presets.
    • Reset the clock.
    • Do the PCM idle learn procedure and the power window control unit reset procedure.
Upper anchor bolt installation
Lower anchor bolt installation

Seat Belt Buckle

  1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
  2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
  3. Remove the front seat.
  4. If equipped, remove the center table.
  5. Remove the under seat storage box.
  6. Remove the center cover, driver's, passenger's.
  1. Driver's: If equipped with seat heater, remove the harness band (A), and disconnect the seat subharness connector (B). If equipped without seat heater, detach the seat belt switch connector clip (C). Detach the seat belt buckle tensioner clip (D), and harness clip (E).

Dec 11, 2017 | 2003 Honda CR-V

1 Answer

How do iremove front seat from a 1997 honda accord


1. Make sure you have the anti-theft codes for the radio and the navigation system, then write
down the frequencies for the preset buttons.
2. Tilt the steering wheel all the way up and telescope it all the way in.
3. '04-07 models passenger's seat: Carefully insert the tip of a small screwdriver (A) through
the hole in the back of the front seat belt lower anchor cover (B) and into the hole in the
front seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.
Remove the screwdriver, and then detach the front seat belt anchor plate (D) and anchor
cover from the lower anchor.4. Slide the seat all the way forward, then remove the seat track end covers from the back of both seat tracks.5. Slide the seat about half way to the rear so you can access the seat mounting bolts. If equipped with the driver's 8-way power seat, fully raise the seat.
6. If equipped with a side airbag, disconnect the negative cable from the battery, and wait at
least 3 minutes before removing the seat. 7. Remove the bolts securing the front seat. 8. Lift up the front seat, then detach the harness clip and disconnect the connector.
If equipped, the seat heater connector on the 2-way power seat and passenger's
manual seat. '04-07 models, disconnect the seat position sensor subharness connector on the
driver's manual height adjustable seat and the driver's 8-way power seat.
9. With the help of an assistant, carefully remove the front seat through the front door opening. 10. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting bolts
before reinstallation.
Make sure each connector is plugged in properly.
Tighten the seat mounting bolts to the specified torque in the sequence shown.
Slide the seat all the way back and tighten then slide it forward and
tighten Before attaching the lower anchor bolts, make sure there are no twists or kinks in
the seat belts. 04-07 models passenger's seat: The triangle marks on the anchor plate and
the lower anchor must face the same side. Insert the anchor plate into the lower
anchor, and make sure that it is locked securely. If equipped with a side airbag, reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and navigation system, then enter the radio station presets. Reset the clock. Your all done. Drink a cold beverage and enjoy the rest of your weekend! hope this helps. Dave

Jun 16, 2011 | 1997 Honda Accord

1 Answer

My Jeep Wranglers driver seat belt will not work.


DO NOT TRY TO FIX IT....an unsafe belt is like a gun with the safety off.please replace it asap.its an easy job to do,just remove the trim and the bolts are in front of you....

Jul 09, 2010 | 1995 Jeep Wrangler

1 Answer

Remove front seat


SECTION 501-10: Seating 1998 Escort/Tracer Workshop Manual REMOVAL AND INSTALLATION Seat —Front Removal
NOTE: Driver side seat shown, passenger side seat similar.
  1. Slide the seat to its rearward position.
  1. Remove the front seat track to floor front bolts.
  1. Slide the seat to the forward position.
  1. Remove the front seat track to floor rear bolts.
  1. Disconnect the safety belt warning indicator switch electrical connector.
  1. Remove the front seat.

Dec 06, 2009 | 1998 Ford Escort

1 Answer

How do I replace a drivers side front seatbelt on a ford mondeo


well the seatbelt in the front of a car are very strong and should be bolted in both from the underneath of the car in the middle and on the edge of inner door seal, most upto date cars there will be a cap which removes from angle at top most point of seat belt to undo. all bolts should be lock tighted(chemical metal) to seal and not undo in unlikey event of bad crash.

Feb 25, 2009 | 2008 Ford Fusion

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...