Question about 1992 GMC Sonoma

2 Answers

Back up lights

My 1992 gmc sonoma's back up lights just quit working. I checked the bulbs and the fuse and they are fine. What else could it be?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had same problem you need to take the back up light switch out of the side of transmission, then push the ball in by hand make sure switch is good if it is you need to grind off about an eight of an inch off the mateing surface of the switch (so it goes further into the transmission) that simple but took me all day to figure out my back up lights work fine now good luck!

Posted on Feb 22, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

The back up light switch. It screws into the side of the transmission, usually drivers side. It should be round in shape with one or two wire connection.If you are going to do it yourself, loosen it with a wrench or socket, then the rest of the way by hand,some fluid might leak out of tranny. Take the old one with you to match it with the new one. Some have the long shaft, and some are short.

Posted on Jan 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1992 gmc Sonoma 4.3 vin z, I ran out of gas put gas it started just fine 3 times stoped filled tank, drive 1.2 miles it died , and won't start, replaced fuel pump , checked all fuses


Test for spark at the plugs and post back. Also, spray a little carb cleaner into throttle body and then try to start it to see if it is a fuel issue.

Apr 15, 2016 | GMC Cars & Trucks

2 Answers

Dash lights not working 2001 gmc sonoma


Check power in and out of dimmer switch.

Dec 24, 2013 | 2001 GMC Sonoma Extended Cab

1 Answer

1992 gmc sonoma fuse box diagram with location of fuses


On my 1992 GMC V-6 Sonoma the fuse panel is located under the left end of the dash board. Fairly close to the foot operated parking brake. There is a small panal covering it, that needs to be unscrewed to be able to see it. Most fuses are identified as to what they are protecting.
The best way to service these fuses is by opening the truck door, with your knees on the ground-- or by laying on your back on the seat with your head in the floor near the parking brake. The truck also has a few inline fuses on wire running directly to the item being protected. If you don't see a fuse in the fuse block for what is not working, find the wire under the hood going directly to the accessory. In-line fuses sometimes look like bulges in the wire, under tape., or they can be straight forward and look like plugs, with a fuse inside. When replacing fuses, use the same size - don't increase the amps, or You'll burn up what you are trying to protect with the fuse.I bought my 92' ,new, when it came out. Mine is the V-6 model. Other versions of the 92, may have different locations for fuses.

Jan 09, 2012 | 1992 GMC Sonoma

2 Answers

1999 gmc sonoma left front signal flashes very fast andand left rear signal or break light work.


Sounds like you need to change the bulb it's getting ready to go out.

Sep 05, 2011 | 1999 GMC Sonoma

1 Answer

I have a left front clearance light out how do you get it out 1


Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
  1. Disconnect the negative battery cable.
  2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
  3. Remove the bulb from the socket; if necessary, replace the bulb.
  4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
  5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
Fig. 1: Common front turn signal/parking light mounting

d16c14b.jpg
Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

8b774bd.jpg
Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

09f4811.jpg

Jul 24, 2009 | 1992 GMC Sonoma

2 Answers

1992 crown vic blinkers stopped working


It can be wiring connections, try to check the wiring coming to the blinkers.

Dec 02, 2008 | 1992 Ford Crown Victoria

1 Answer

1995 gmc sonoma


check your connections in the fuse box, they may not be making a good clean and tight fit, they could have pushed out the rear of the fuse box

Nov 29, 2008 | 1996 GMC Sonoma

3 Answers

Brake lights don't work. Fuse is good, bulb is good, but brakes still won't come on. GMC Sonoma 1994.


please check your brake light switch located near the brake pedal. it could be faulty.

tnx 4 using fixya,

drcool

Sep 24, 2008 | 1999 GMC Yukon

Not finding what you are looking for?
1992 GMC Sonoma Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...