Question about 1992 Mazda 323

Open Question

How to adjust rear handbrake on mazda 323

I wont to adjust the rear handbrake of a Mazda 323

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: ABS, Traction control and handbrake

I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on but speedometer was not functioning and the ABS light was on. The rear ABS senssor was the problem.
SDM

Posted on Jan 23, 2009

nicolas7
  • 1 Answer

SOURCE: my 89 mazda 323 turns over but wont start

Last week my 323 89' Mazda stop working as I was driving it in middle of the street, I pushed to the side. it would not start, the starter sounded ok, but the car just didnt start, I checked the fuses, gas pump, and all seemed to be ok, finally with the help of a friend we found out that the ignition rotor at the distributor wasnt working we then replace it with a new one from autozone , is about 5 dollars, now it works just fine, big problem easy solution.

Victor

Posted on Aug 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Video of how to replace rear wheel bearings of a Mazda 323, 1.3,sting,front wheel power


take the rear hub off
you will need a hydraulic press or a vice to push bearing out and then in.

Jul 09, 2016 | Mazda Cars & Trucks

1 Answer

What is the valve clearance of mazda 323 1.3 engine 94 model


manual adjustment ? then 12th inlet and 15th exhaust will suffice

Mar 12, 2015 | 1994 Mazda 323

3 Answers

Mazda 323 park brake light won't turn off


Theres a little switch that activates the light. It could possibly be sticking

Mar 18, 2013 | Mazda 323 Cars & Trucks

1 Answer

Have just replaced the left rear brake pads on a 1996 mazda lantis, Unfortunately l h handbrake now not pulling up far enough to work, How do you adjust the handbrake as R H side working ok


on rear pads they will automatically adjust up on theri own as the piston will wind itself out unless the vehicle has a handbrake thats seperate with brake shoes inside the read disk and iam not familar with this model to tell you if it is of this later type

May 01, 2011 | Mazda CX-7 Cars & Trucks

1 Answer

I feel the handbrake cable is just needing a little adjustment on my Mazda 6,but cannot find the adjuster underneath or a removal cover on the inside to allow access to the adjuster,any ideas?...


remove the ash tray from the rear console there you will see the adjustment for the e-brake heres a picture to help you . hope this is helpful.26ca85d.gif

Jan 24, 2010 | 2004 Mazda 6

1 Answer

I HAVE A MAZDA 323 1999 MODEL CAN ANYONE TELL ME HOW TO ADJUST THE HANDBRAKE PLEASE please note it is a 1999 model but it wont let me put that year in


your handbreak connects to the rear breaks follow the cable from your break drum where the 2 meet is the ajustment give it a squart of penertrating oil before ajusting as it has been open to the weather also there is further ajustment where the cable enters the hand break lever good luck ps if this dosent do the trick i suggest you cable is fully streched you will need to fit a new one

Nov 15, 2009 | 1986 Mazda 323

2 Answers

Mazda 323f sport 1999. How do you adjust parking brake?


Where the handbrake lever is,it will be covered by a boot of some sort.Peel this back and beside the lever will be either a rod with a nut on it,or it will have a recess for a screwdriver.with the h/brake off,do the adjustment by tightening it.When it's right, the h/brake should have to be pulled so 7 'clicks' can be heard.Hope this helps

Aug 19, 2009 | 1994 Mazda 323

1 Answer

Replaced rear calipers and need to know where to adjust emergency brake, 1999 mazda 626


Not 100% sure but peel back the handbrake lever cover.Beside the lever where the handbrake cable attaches there may be an adjuster there.Either directly on the cable itself or by locknuts threaded on the cable.Hope this helps

Aug 02, 2009 | 1999 Mazda 626

2 Answers

ABS, Traction control and handbrake light is on. Car was running on 3 cylinders previous to the lights coming on. 1999 Mazda SP20 Familia (323)


I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on and the ANSWER was a speed sensor which is to do with ABS system needed replacing. You can determine which one is broken by putting volt meter over each of them.

Nov 17, 2008 | Mazda 323 Cars & Trucks

1 Answer

Handbrake not engaging!!! ;o(


did you pull the plug out of the back of the calper and adjust the caliper after the new pads were installed?

Nov 15, 2008 | 1992 Mazda MX-3

Not finding what you are looking for?
1992 Mazda 323 Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...