Question about 1999 Chevrolet S-10 Pickup

1 Answer

Starter 99 s10

How do i change starter on 99 chevy s10. I have bolts out but cant acsess the wires

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

First disconnect the positive battery cable. You already have the bolts out. pull the starter back and down and it will drop out. do not let it hand from the wires. Disconnect the wires to the starter. Pay attention as to which wire comes off what terminal. They must be attached correctly or your starter will not crank after installation. Then the last thing you do will be to hook the battery up again.

Posted on Feb 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i take the starter off from my car 99 chevy prizm


it comes in from other side on the trans housing

Aug 03, 2012 | 1999 Chevrolet Prizm

1 Answer

Instructions on how to change a starter on a 1992 chevy s10 blazer 4.3z engine v6


The positive doesn't even need to be disconnected. That should be the 'negative' terminal that you disconnect first, not the 'positive' one. The negative terminal is safe to accidentally ground your tool, but if you ground your tool disconnecting the positive terminal you can damage your battery, tool, or even injure yourself.

Now to get the starter out; Use jack stands to hold up your S10 front end, remove the right side motor mount bolt (the horizontal one), then use wood blocks and your jack to lift up off the bottom of the transmission. Look at the motor mount from above and you will see that it has been raised two inches or more, give the transmission maximum lift without lifting the vehicle off of the jack stands.

Be careful to not upset you vehicle! Push on either side and the front or rear to make sure that it's secure before crawling underneath.

Have a light source ready. From underneath, lift the end of the starter up and away from the oil pan, the other end should come out the of the bell housing. Now for the tricky part, either end can come out but it comes out like puzzle piece, if you take out the motor end first start out vertical until it stops then move until it's closer to horizontal. It's very tight but it will come out.

Installing I could not just reverse my instructions so I put the driver side in first and it just plopped right in. There was no skill in getting it out or putting it back in, just luck, it's that tight.

Hook up your terminals on the starter with the solenoid orientated to the bottom, rotate to proper orientation then place in the bell housing. Start your two vertical bolts, and now you're on easy street.

My opinion of these design is low. It's a lot of work to change the starter on this unit. Good luck to anyone reading this!

Apr 16, 2012 | 1992 Chevrolet S-10 Blazer

1 Answer

How do i remove and replace the starter on a 93 s10 Chevy blazer


There should be two bolts and a big wire comming from the battery to remove. I always do the wire first then the two bolts. You have to be careful starters are heavy when you are on your back under a truck. All of this is located on the same side as the battery you can fallow the red wire from the battery to the starter if you need help locting it. The starter is not hard to change but there is very little room to move it in and out of position so it takes a little bit of time.

Nov 26, 2011 | Cars & Trucks

1 Answer

How do you change speed sensor in 99 chevy s10 pickup 2.2 motor 2wd?


Drivers side rear of the transmission at the tail shaft. If it's a manual trans it will screw in and it auto it will have a metal tab with a bolt holding it in place.

Jul 30, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

How do I replace my starter?


Open hood.
Disconnect negative (-) batter cable
Locate the starter (under vehicle).
Remove electrical connections. (be sure to remember/take a picture/ make a drawing/ or mark which wires go to what posts)
Remove mounting bolts.
Remove starter, replace with new starter
Install mounting bolts
Install electrical connections

Jan 06, 2010 | 1990 Chevrolet S-10 Blazer

1 Answer

Need detailed directions to remove starter from chevy s10


disconnect negative battery terminal unbolt starter from engine i think they are 14mm bolt maybe 15mm and take the 2 wires off making sure when you install new starter the wires go back where they came from the starter should come right down the reinstall in reverse order

Nov 11, 2009 | 1995 Chevrolet S-10 CA Edition

2 Answers

How do i remove the starter from my s10 chevy truck 2000


remove your positive lead from the battery. Climb under the vehicle and remove the 3 wires attached to the starter, remove the 2 bolts holding the starter in place, install new starter in reverse order.

Sep 16, 2009 | 2000 Chevrolet S-10

2 Answers

Chevy S10 Pickup Starter. Removed the two bolts


Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Mar 14, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

1999 Chevy S10


Just pull the dash back a little by undoing all the bolts and screws, its going to be a tight fit find someone with small hands.

Oct 21, 2008 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
1999 Chevrolet S-10 Pickup Logo

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...