Question about 2000 GMC Jimmy

2 Answers

Where is my 1 2 shift sensor 2000 gmc jimmy

I need the location of my 1 2 and 2 3 shift sensors 2000 gmc jimmy 4x4

Posted by on

  • 2 more comments 
  • Anonymous Mar 12, 2014

    new transmission won't shift right

  • Anonymous Mar 16, 2014

    wanting to install an airlift kit in my 2000 gmc jimmy

  • Anonymous Mar 17, 2014

    is there a brake controller hookup under the dash on a 2000 gmc jimmy

  • Anonymous Mar 22, 2014

    hung up near the antennae



2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 180 Answers

Inside trans. pan at the rear of the valve body. They have a wire clip which holds them in.

Posted on Jan 21, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • GMC Master
  • 3,854 Answers

Your transmission is electronic, it read's the the speed sensor from the yoke and relay's the information to the ECM which tell's the servos in the transmission acivate to change the gears up or down with the engine out put.

Posted on Apr 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the evap purge solenoid sensor on a 1997 jimmy

where is the evap sensor on a 1997 gmc jimmy 4x4 6 cylinder

Jul 25, 2012 | 1997 GMC Jimmy

1 Answer

My 2000 jimmy wont shift into 3rd or 4th and it reaches 3000 or more rpms. its an automatic transmission. someone said it could be speed sensors. where are they located.

Its more than likely a shift solenoid sticky causing this problem.Its located inside the transmission oil pan in the valvebody.

Dec 03, 2011 | 2000 GMC Jimmy

2 Answers

Where is the speed sensor located on a 93 jimmy 4.3 4x4 and is there any sensor on ****** that would be involved or cables?

The vehicle speed sensor(VSS)is located on left rear of transfer case on 4x4( 4wd) 1993 jimmy.Ensure ignition is off.Raise and support vehicle .Disconnect VSS electrical connector.Place a container under VSS mounting area, to catch transmission fluid when VSS is removed.---- On 4wd the VSS is threaded,un-thread VSS from transfer case.Then remove VSS and O-ring.Installation in reverse.--------- This will help.Thanks.Helpmech.

Aug 05, 2011 | GMC Jimmy Cars & Trucks

1 Answer

2000 gmc jimmy need to know where the crankshaft sensor is located as im told that is the most likely culprit. its a 4.3 vortec 4x4 slt model if that helps.

Hello jerryparker6,
The image below shows the location of the crank position sensor.

I hope this helps.



Apr 11, 2011 | GMC Jimmy Cars & Trucks

1 Answer

Where is shift actuator located on 1999 Jimmy 1999

I had the same problem with my 1999 Silverado which would blink several times on the mode I selected then go back to the 2 wheel High. I found the switch module to be defective, after replacing it I have never had the problem again.

Nov 22, 2010 | 1999 GMC Jimmy

1 Answer

I can't find the crank sensor in my 2000 gmc jimmy 4x4 4.3 6 cylinder

look way down at the bottom of the engine right behind the crank shaft pully and the balancer u should se the wires on the pasenger side they usualy are facing slightly down and there is only one bold holding it in.

Nov 18, 2010 | 2000 GMC Jimmy

1 Answer

2000 Jimmy giving me some problems.

The reason you engine over heats is the engine cooling fan(s) are not coming on. They run by a coolant sensor and a fan relay.
You may also want to make sure you have the proper amount of coolant in your system.

Is your Jimmy a push button 4x4, or do you have to pull a lever to shift to 4x4 ?
Please let me know so I can help guide you through either of these repairs.
We aslo have the parts you need :
click on the contact.

Feb 12, 2010 | 2000 GMC Jimmy

1 Answer

On my 1997 jimmy 4x4,will not shift into 4weal drive, high or low never done this before.

is it electric push button
if so its a sensor on the transfer case an or one of the wheels.....
if its manuel then the main shaft is striped....
or its seezed under your jimmy an dont wanna shift

Jan 04, 2010 | 1998 GMC Jimmy

1 Answer

Help on GMC jimmy

It sounds like you need a transmission output speed sensor.

Aug 16, 2009 | 1999 Chevrolet Blazer

1 Answer

Where is my 1 2 shift sensor

what kind of car do you have

Jan 21, 2009 | 2000 GMC Jimmy

Not finding what you are looking for?
2000 GMC Jimmy Logo

Related Topics:

565 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides