Question about BMW X3 Series

Open Question

My BMW x3 jerks when accelerate

My x3 jerks when accelerating and clunking noise

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: my 05 xc 90 d5 is making a clunking noise when

It sounds like it may be something to do with the engine mounts. I had a similiar problem with my 04 d5 and it was down to 2 of the mounts wearing. They have a rubber damper for vibration which can wear out and then the engine moves slightly when its under load and when braking. Best to get it checked out although it sounds a lot worse than it actually is. Apparently the mounts I had fitted were a revised version which are more suited to the job.

Posted on Jun 22, 2009

Ad
  • 1 Answer

SOURCE: car jerks when accelerating 1998 mazda millenia v-6

Could be a T C S sensor that needs replacement.

Posted on Jul 03, 2009

  • 83 Answers

SOURCE: Clunking noise in rear when accelerating

check rear u joints for wear.

Posted on Jul 26, 2009

bunnydawg
  • 5158 Answers

SOURCE: front diff gone, car making clunking noise on acceleration

go to an empty parking lot

turn the wheel all the way to the right and drive in circle slowly

listen for a ticking noise or similar.

repeat in the left direction.

if you hear a ticking or clicking noise you likely have a bad CV joint. not a horridly expensive repair tho a necessary one

one other thing that will cause it is if the rubber boot surrounding the CV
joint is torn.

pleae take a moment to rate this solution.

robert

Posted on Sep 04, 2009

jigsaw_9077
  • 308 Answers

SOURCE: When i accelerate there is hesitation and jerking?

It means there is a problem in the carburetor of your car . But if then so you still have to check the accelerator springs and pedal. For there are worn out or destroyed parts then replace them for good .About the carburetor.Prepare the equipment or tools to be used in servicing the carburetor .So that when carburetor will be repaired or serviced no parts will be damage or lost. Locate the carburetor. Disconnect the fuel lines , the accelerator cable and the magnetic jet from the carburetor.Dis -assemble the carburetor.Clean carburetor with carburetor cleaner.Don't forget to observe safety rules. If there are worn out parts or destroyed parts then replace them .But you the owner don't have time to do the job then go to a car shop mechanic and let them do the job.

Posted on Oct 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clunk under car on acceleration, but goes away after first initial clunk.


I would check the spark plugs and wires or coil packs. Sounds like the ignition system is arcing.

Sep 01, 2015 | 2007 BMW X3 3.0si

1 Answer

Clunking noise from back end bmw x3


i think this is a rear drive car so the boot might be going inspect the rear boot for grease leaks near the tire

Mar 23, 2014 | BMW X3 Series Cars & Trucks

1 Answer

My 1999 jeep grand cherokee is making a loud clunking sound when I accelerate and then starts sputtering/jerking until I reach about 70mph


the bad news is that when that noise starts is either 3 things
1. your rod bearing has slipped and is about to break
2. you have a stuck lifter
3. finally you may be just low on oil

Nov 25, 2013 | Cars & Trucks

1 Answer

Clunking noise when accelerating and at dead stop...


the a/c clutch and or bearing is bad.

Nov 17, 2013 | 2006 BMW 330i

1 Answer

Noise upon acceleration


Can you describe what the noise sounds like? Is it a clunk, a wine, a thump . . ?

Jan 10, 2013 | 2006 BMW Z4 Roadster

1 Answer

02 yukon denali has a whining noise similar to bad wheel bearings. wheel bearings were just replaced. could it be cv's, no clunking sound though. also, sometimes the vehicle ''jerks'' when accelerating,...


the jerking and noise you are experiencing is the drive chain and bearings in the transfer case also you may want to check the end play in both front and rear pinion bearings and yokes

Jan 22, 2010 | 2002 GMC Yukon Denali

1 Answer

Clunking noise in front under acceleration. If rolling in neutral no noise, accelerate under load, hear clunking noise from left front


99% a motor mount which should run about $100 to replace or the left front axle which will run you about $150

Sep 24, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...