Question about Mitsubishi Montero Sport

1 Answer

Where is the crank angle position sensor on a 99 montero sport 3.0 liter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 14,384 Answers

Click here to see Nick.

Posted on Jan 11, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
keemo68
  • 1263 Answers

SOURCE: is it possible to adjust a throttle position sensor on a 2000 montero sport?

when your vehical throws a code and you replace the defective part, you must clear the code or the ecm will still recognize it as an active code.

Posted on Aug 27, 2008

  • 701 Answers

SOURCE: need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter

Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two wires plugged in to it. Please rate this answer as this lets us know you received the information you asked for. Should you need further help please just ask. Thank You for using FixYa. Roger

Posted on May 06, 2009

co7196
  • 3433 Answers

SOURCE: Where is the crank shaft positioning sensor

Look at the area around the crankshaft pulley. It's bolted to the block and senses the crank position. If it fails, You won't have an ignition spark. Good Luck, Ned

Posted on Aug 27, 2009

  • 6982 Answers

SOURCE: 1999 jeep cherokee sport it wont start cranks but wont fire

Figures...I'd use 2&3 as b&c Open reading means that with the meter set to ohms and turned on, the meter should read the same connected to the terminals as it did before you connected it.

Posted on Oct 29, 2009

drsinister69
  • 2317 Answers

SOURCE: mechanical or hydraulic lifters for my '99 montero sport??

Hydraulic

Posted on Mar 16, 2010

Testimonial: "thank you. i appreciate it"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located on the 2002 Mitsubishi Montero sport xls 3.5 truck.


Hi David, The link below is how to test the crank sensor (1997-2004 3.0l Montero, Hope this helps......CHEERS
http://easyautodiagnostics.com/mitsubishi/3.0L/crankshaft-position-sensor-test-1#3
The crankshaft position (CKP) sensor is located behind the timing belt... but testing it is done without removing the timing belt or its components. This is due to the fact that the crank sensor's connector is located on top of the engine and in plain view (next to the ignition control module). In the photo below, the orange arrow points to the location of the crankshaft position sensor connectors (photo applies to: 3.0L 1997-2004 Montero Sport).

Mar 31, 2016 | Mitsubishi Cars & Trucks

1 Answer

2000 mitsubishi montero sport 3.0 liter getting p0340 code


an aftermarket sensor can cause this-electrical generics can hav this issue--but the hardware that it is set upon cud be bad-may need a inspection by a pro---usually when a belt is replaced-the tensioners and guides etc are also done--chec out procedure in a chilton repair volume at ur library

Mar 25, 2015 | 2000 Mitsubishi Montero Sport

1 Answer

Where is the crank sensor located on 1999 montero sport


Crankshaft position sensor A (24x) is behind the crankshaft pulley.

Crankshaft position sensor B (7x) is on the lower back side of the engine block.

May 12, 2014 | 1999 Mitsubishi Montero Sport

2 Answers

Montero Sport 99 crank but no start,what could be the problem?


when you turn the key to the start position do you hear the fuel pump

Dec 02, 2012 | Cars & Trucks

1 Answer

Need a fireing order for 01 mitsubishi. montaro sport v6


there are a few different engines. A 3 liter with or without a distributor, and a 3.5 liter. All V-6 engines have firing order 1-2-3-4-5-6. See figures below:

3 liter engines:

jturcotte_553.gifjturcotte_554.gif

3.5 liter engine:

jturcotte_555.gif

Dec 19, 2010 | 1999 Mitsubishi Montero Sport

2 Answers

Where a part is


LOOK ON LOWER SIDE OF CYLINDER BLOCK.

Jul 04, 2010 | 1997 Mitsubishi Montero Sport

1 Answer

Jeep wrangelr Crank Position Sensor


wall5552: there were two engines used in 1992 Jeep Wranglers.
A 2.5 liter and a 4.0 liter. HOWEVER>>>> The location for the crank angle sensor is the same for both.
It is located on the bell housing up near the front at about the 10:00 PM position.
The Cam position sensor is located in the Distributor on both engines as well.

May 10, 2009 | 1992 Jeep Wrangler

1 Answer

Starter cranks slow


By your description I would say BATTERY. Don't know how old the battery is. The average life of a battery is about 3 years, sometimes less, sometimes more.

Mar 31, 2009 | 1999 Mitsubishi Montero Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...