Question about 1999 Ford Econoline

Open Question

Valve cover removal 99 ford van - 1999 Ford Econoline

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
gypsycat00
  • 224 Answers

SOURCE: how to remove the valve cover to replace gasket

What kind of engine? If it's a 3.0L Vulcan, you have to take off the upper and lower intake manifolds and you'll be able to take the valve covers off. There's a bunch to take off before you get to that point. The EGR Valve, Throttle body assembly, ignition coil pack, etc. Make sure you relieve the fuel system pressure (it might be behind the right side well cover of your trunk- disconnect that connection), and take off the negative battery terminal before begining work.

Posted on Jun 13, 2009

Ad
  • 216 Answers

SOURCE: how to change valve cover gasket on a 99 ford

remove spark plugs and high tension cords/ remove the valve cover bolts using socket wrench/ use screw driver to lift up the valve cover/ clean the lid/ put a new gasket and put silicone gasket sealant on the edge of half moon rubber gasket to avoid leak/ tighten the bolts/ put the plugs and wire back...

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 ford f550 diagram on how to remove glow plugs


with the engine "stone cold," disconnect battery, remove valve cover, disconnect glow plug connector, remove glow plug with a 10 mm deep socket, install new glow plug (torque to 13 ft.-lbs.), and reattach connector. After finishing the remaining 3 glow plugs on that bank, clean valve cover, install new gasket, and reinstall valve cover. Do the same thing for the other bank of glow plugs and reconnect battery. Not a difficult job--should take several hours.

Jun 14, 2011 | 1999 Ford Super Duty F 550

2 Answers

Where is the fuel filter and pcv valve on a 1993 G20 van


Hi!!
PCV valve located under engine cover, top of engine, mounted in passenger side valve cover

Fuel filter is located Under vehicle, passenger side, below seating area, front of fuel tank, mounted on chassis DON'T FORGET TO RATE THIS POST!!

Aug 23, 2010 | 1993 Chevrolet G20

2 Answers

Engine number


I have a 99 ford E350 15 pass van with the V10 gas engine with 120,000 miles and auto trans. The engine was missing at speeds above 45 MPH. I took it to a repair shop for a tune up. They changed the spark plugs and charged me $520.00. Well now it misses at idle to 55 MPH. They made it worst! I'll eat my losses and will not deal with the repair shop as they are giving me the run around. Can anyone help me before i get ripped off again. My last resort is the Ford dealer but they are the biggest rip off in the world.
Need help,
Harold

May 10, 2010 | 2002 Ford E350

1 Answer

Need to find the pvc valve on 99 Ford Explorer V6 ( location.) Where is it located at on engine.


it on the valve cover...you have 2 valve cover..it on the right valve(the one with no engine oil cap on)..

Apr 21, 2010 | 1999 Ford Explorer

1 Answer

Where is the pcv valve located on 1995 ford econoline e 150 van engine where do i put it


depending on the engine. most likely either the center of the lower intake manifold at the back(5.0) or right hand valve cover at the back(5.8) remove the doghouse(engine cover under the dash) should be visible

Apr 11, 2010 | 1995 Ford Econoline

1 Answer

How to change valve cover gasket on a 99 ford taurus


remove spark plugs and high tension cords/ remove the valve cover bolts using socket wrench/ use screw driver to lift up the valve cover/ clean the lid/ put a new gasket and put silicone gasket sealant on the edge of half moon rubber gasket to avoid leak/ tighten the bolts/ put the plugs and wire back...

Apr 07, 2010 | 1999 Ford Taurus

2 Answers

Pcv valve location


it is normally located on the valve cover itself look for the black tube going into the top of the valve cover gasket

Feb 04, 2009 | 1999 Ford Windstar

1 Answer

99 explorer xlt v8


You have to remove the upper intake and it's at the rear of the pass. side valve cover.

Jun 10, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
1999 Ford Econoline Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...