Question about 2008 Mazda B Series Pickup

1 Answer

What size engine do i have

I was told that it is a 2200 from a 88. Stamped under the top timing belt cover it has 1.6 & 1.8 please help

Posted by on

  • 1 more comment 
  • wahhill05 Jan 21, 2009

    Sorry dont know were the 2008 came from. i have a 88 motor with 1.6 & 1.8 stamped 0n it

  • wahhill05 Jan 21, 2009

    thank you this very helpful

  • yadayada
    yadayada May 11, 2010

    don't understand the question, this engine was replaced? why on a 2008 model? this is the correct model year of the truck? please explain what u have here, what year.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 61,289 Answers

The 88 B series engine is 1.8L, the reason it shows 1.6 and 1.8 is because they are the same eng block series, just like a chevy small block V8 comes in 5.0L, 5.7L and 6.6L but all are the same basic block.

Posted on Jan 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1972 engine. What size is it and what did it come out of?


That is a casting number for a 351c block, casting date is October 22nd 1971. The same casting number was used for the 4 bolt and 2 bolt main blocks.

Nov 28, 2015 | Ford Cars & Trucks

1 Answer

Re-sealing timing belt cover 2007 Camry


wow no engine stated, post engine size.
depends if mechanic is size of squirrel or a gorilla.
huh?
why not longin to alldata. com and read the page on timing belt changeout.
you can goggle this, 1000s of hits, why not ?

there are serious costs to do service on most FWD cars.
next time buy a RWD car. far easier to fix.
FWD is cheaper to make, (pull rad, fix, put back Rad)
there are 3 engines. ill roll the dice, and log in to alldata.
and see. 37steps out and 37 steps in,
about
not one word, TO pull engine, 2AZ-FE CHAIN
THE 2GR-fe ENGINE IS CHAIN TO.
see step 29, your posted ITEM>!!
PASTED, 2gr CAM BELT SECTIONS;
  • 2007 TOYOTA Camry HV

1. REMOVE LUGGAGE TRIM SERVICE HOLE COVER
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
4. REMOVE FRONT WHEEL RH
5. REMOVE ENGINE UNDER COVER LH
6. REMOVE ENGINE UNDER COVER RH
7. REMOVE FRONT FENDER APRON SEAL RH
8. DRAIN ENGINE OIL


10. REMOVE NO. 2 ENGINE MOUNTING STAY RH
11. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY
12. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH
13. REMOVE V-RIBBED BELT TENSIONER COVER SUB-ASSEMBLY
21. SET NO. 1 CYLINDER TO TDC/COMPRESSION
22. REMOVE CRANKSHAFT PULLEY
23. REMOVE CRANK POSITION SENSOR
24. REMOVE OIL PAN SUB-ASSEMBLY
Remove the 12 bolts and 2 nuts.
Insert the blade of SST between the crankcase and oil pan. Cut through the sealer and remove the oil pan.

25. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Remove the 2 nuts, tensioner and gasket.

Do not turn the crankshaft without the chain tensioner.
26. INSTALL ENGINE HANGERS
Install the No. 1 engine hanger and No. 2 engine hanger with the bolts as shown in the illustration.
  • Attach the sling device to the engine hangers and chain block.
27. REMOVE ENGINE MOUNTING INSULATOR
Attach the engine chain hoist to the engine hangers.
  • Do not attempt to hang the engine by hooking the chain to any other part.
  • Remove the bolt and disconnect the engine mounting insulator FR.
  • Remove the 4 nuts from the engine mounting insulator RH.

  • Raise the engine and remove the engine mounting insulator RH.
28. REMOVE ENGINE MOUNTING BRACKET RH
Remove the 3 bolts and engine mounting bracket RH.
29. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
30. REMOVE TIMING CHAIN CASE OIL SEAL
31. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
Remove the crankshaft position sensor plate.
AND SO ON,,,, end. quote.

AS YOU CAN SEE ITS NOT A MOTOR PULL BUT IS UNMOUNTED
AND FLOATED,

Now begs the question, which is less work. the above, or just pull the engine, and work sitting down. easy work and higher quality
may that depends on the person and his/her size.

Jan 08, 2014 | Toyota Camry Cars & Trucks

1 Answer

Need to know how to replace the belts on a 1992 Honda accord.


How to dismantling and change timing belt for CB7 engine:
1. remove elektrik power (+) from accumulator
2. put suport on below engine
3. remove the bolt and left engine mounting
4. remove upper engine cover
5. open side engine cover (timing cover from black plastic)
6. please remember top marking on the crankshaft
7. make to slack tensioner wheel, and remove the belt.

note : there are two timing belt on cb7 engine, smaller and bigger

you can try
my number call +6281808024008 (Dede)

Jul 12, 2011 | 1992 Honda Accord

1 Answer

I have a 2004 suzuki forenza and one mechanic told me that the engine was gone and another told me it's probably the timing chain, how do you know which is which?


Neither are hugely wrong.

Does it have a timing chain or belt. If it has an over square engine and the timing chain or belt has snapped, then the valves which let in the fuel and air and let the exhaust gases out travel up and down driven by the cam shaft and the pistons will travel up and down driven by the crank shaft. Without the belt or chain to keep them timed, they meet with great force, at least a top engine rebuild.

To check if the timing chain or belt has broken, you'll need to take the belt/chain cover off. Disconnect the battery first.

If its an under square engine, the pistons have a longer bore to travel, the pistons and valves don't meet.

Jun 25, 2011 | 2006 Suzuki Forenza

1 Answer

My motor hols back on power, I think the timing is out, how can i rectify this?


You will need a timing light. Connect it to the No 1 spark plug, run the hot engine at idle speed and adjust the distributor until the timing marks on the front pulley line up with the timing mark in the cam belt cover, This is the basic method. Depending on where you are situated, anti pollution settings come into play and things like Digital idling Stabilisers need to be bypassed, or vacuum pipes need to be disconnected. Also timing points differ and could be anything from 7.5 degrees before top dead center to 3 degrees after top dead center. Engine types and specs are all related to the engine codes which are found either on the engine data plate or stamped on the engine block.

Jan 17, 2011 | 1985 Volkswagen Golf

1 Answer

Hi - I would like to reset the timing on a 1993 Mazda 626 2L 4 cyl engine. Could you please help me.


timing an engine is a time consuming process to begin timing an engine you must 1. find the 1 cylinder 2. remove the timing belt cover 3. remove the spark plug form the 1 cylinder 4. put a screwdriver into the spark plug hole 5.rotate the timing belt until the cylinder is at the top of the chamber (thats what the screwdriver is for) 6. mark the top of the timing wheel with a pastel marker 7. with a timing light set the idle speed to the factory settings if you dont have a timing light you can normally get it fairly close by listening

Jan 09, 2011 | Mazda 626 Cars & Trucks

1 Answer

Daewoo lanos 1.5l timing belt marks


Answer

If this is a single overhead cam, possibly A15SMS (engine type):

If you have everything stripped down and can see the crank shaft gear, you will notice an arrow stamped into one of the gear teeth.
this arrow must point towards the bottom, you will notice a mark (notch) cut into the housing, line the arrow on the gear with this notch.

remove the four 10mm bolts that secure the top cover of the timing belt, gently open the cover (not removing it) to see the Cam Gear. You will not be able to remove the cover because of the design.

The Cam Gear should have a line stamped into one of its teeth, this should be pointing up and towards the top. On the inner cover you will notice a notch in the casing, line both up together if it is not already.

You can check the following if unsure:
Remove # 1 spark plug (nearest the Cam Belt) and place a long screwdriver in the hole carefully to feel the piston is at the top, #2 and 3 will be down and the last one #4 at the distributor end will also be up.

Remove the rocker cover and you should see the Cam loabes on #1 piston free, (no pressure on the cam shaft) meaning the valves are closed.


tim

Dec 06, 2010 | 2001 Daewoo Lanos

1 Answer

Bought new battery but car won't start. Is it the timing chain?


Take the timing belt cover off to inspect the condition of the belt. Look for any missing teeth & tauntness of belt. You may have to replace it.The engine may be out of time with the cam shaft. It's hard to go any futher without knowing engine size. Good luck!

Dec 26, 2009 | 2002 Pontiac Grand Am

1 Answer

How do i change a 1997 mirage timing belt


This is a hard job to do if you have no experience please don't hurt your self,,,,first raise the car remove tire remove all belts,remove a/c bracket,timing belt cover put jack under oil pan and raise the motor remove side engine bracket set a side remove top valve cover remove the spark plugs and turn the camshaft flywheel clockwise and bring # 1 piston at top dead center (the highest point) check the crankshaft should align at the mark loosen timing tension remove belt,do reverse procedure..

May 11, 2009 | 1997 Mitsubishi Mirage

1 Answer

Engine


It is stamped on the top side of motor which model it is. Left middle of motor just behind belt cover.

Feb 23, 2009 | 1999 Subaru Impreza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...