Question about 2008 Ford Edge

Open Question

Check park assist message on. sensors will not engage. edge 2008

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service park assist message. I replaced all 4 sensors and wiring harness at bumper. Vehicle was never in accident.


I not sure what the problem is but I do know if you back up over five miles per hour the park assist will shut down in reverse and you will get a message to that effect on the dash. I had the same problem with one of mine and the dealer told me that it is designed that way to shut down. Try backing up under five miles per hour and see if you have the same problem. Hope this helps.

May 21, 2015 | 2008 GMC Yukon

1 Answer

2008 Cadillac escalade won't start and dashbord says service suspension system and parking assist off what does this mean?


steering wheel position sensor may fail, resulting in the service stability message being displayed.

May 06, 2015 | 2008 Cadillac Escalade

1 Answer

HOW DO YOU TEST THE PARK ASSIST ON A 2007 FORD EDGE


Check with a diagnostic scan tool for module fault codes and sensor fault codes. If nothing comes back complete electrical circuit prove out.

Feb 03, 2015 | 2007 Ford Edge SEL Plus

1 Answer

How do I fix "Park aid data error"


In many cases when you accidentally do this the codes set in the module that controls this will need to be cleared before the system will start working again. This can be done with a high end scan tool (anything that costs at least $1,500 or more. A code read will not be able to do this.

I just ran into a simular problem replacing the oil cooler on a BMW M5. I started the car before putting the front bumper back on to check for leaks. The front sensors where not plugged in and the park assist was disabled. I had to clear the codes in the park assist module to get it working again.

Jul 27, 2014 | 2008 Ford Fusion

1 Answer

2008 Silverado 6.0 V8 auto 2 wheel drive linkage problems i think?


yes its the break senor that detects ur use of the relase lever when u press on the break it enable the sensor to relay the message to the brain

Nov 29, 2013 | 2008 Chevrolet Silverado 1500 2WD

1 Answer

My park assit is on and the sensor are not working for backing up can they have dirt in them


{: ) The PARK ASSIST OFF message will be displayed when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged. • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.

The SERVICE PARK ASSIST message will be displayed when the object alarm module detects a malfunction in the parking assist system and the system is disabled. It could be one of your sensors is at fault or even the module.

May 18, 2011 | 2007 GMC Yukon Denali

1 Answer

2005 Lincoln Navigator. Message says to Check


Most likely the problem you are experiencing with the park assist is a fault in one of the sensors mounted in the rear bumper. I would not consider it to be a major fix, however there will be a few hours labor involved as the bumper cover needs to be removed to replace the sensors.

Jul 07, 2009 | 2003 Lincoln Navigator

3 Answers

What does "service park assist system" mean on my 2008 jeep?


The park assist system detects objects 59 inches or less in back of your vehicle, to warn u so u don't strike the object. I'm guessing that since the service park assist system comes on in the ice and snow, the monitor is detecting something (ice and snow covering the sensor). If u clean off the snow and ice, the message should shut off.

Jan 13, 2009 | 2007 Jeep Commander Rocky Mountain

1 Answer

2008 cobalt daytime running lights not working


Check to make sure your parking brake is not partially engaged. If the parking brake is engaged even to one click off from the released position the DRL module will be disengaged. Also there may be a problem with the parking brake position sensor which is responsible for determining if the parking brake is partially engaged.

Oct 31, 2008 | Chevrolet Cobalt Cars & Trucks

Not finding what you are looking for?
2008 Ford Edge Logo

Related Topics:

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...