Question about 2007 Chevrolet Cobalt Coupe

Open Question

Removing oil pan from chevy cobalt stuck - 2007 Chevrolet Cobalt Coupe

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: 2000 Chevy Blazer

i am working on a s 10 of the same yaer and problem i will post my results after tomorrow when i have finished the job i bout this truck cause of the forum i own one that is a great one and this one is for experimental purpose i will let u know so far you cant lift the motor with a jack or a hoist so we r going another route in the mornin

Posted on Dec 27, 2008

  • 135 Answers

SOURCE: i am replacing the oil pump on a 98 chevy malibu,

take loose the motor mount bolt and jack the front of the engine up to clear the oil pump and remove the pan,.the bolt the runs thru the center of the mounts ,the easiest way ,hope this helps you, thanks robert b.

Posted on Jun 30, 2009

juncro
  • 467 Answers

SOURCE: My 1998 chevy s10 blazer 4x4 looks to be leaking

no special way, the oil gasket need to change

Posted on Nov 10, 2009

  • 834 Answers

SOURCE: removal procedure of oil pan for a 1997 chevy

To remove the engine oil pan either the engine has to be lifted all the way off of the motor mounts and the oil pan should just clear the flex-plate and transmission, or the front axle dropped down out of the way, or the transmission and flex-plate will have to be removed.

Usually if the engine can be lifted enough to fit a piece of 2x4 wood between the motor mounts and the frame then the oil pan will usually just have enough clearance to be removed from the rear and the oil pan should just clear the transmission and the flex-plate. Also, be sure to check that the fan blade does not damage the fan shroud when lifting the engine.

Let me know if you require any further assistance.

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 chevy cobalt. I apparrntly hit something in the road and got a hole in my oil pan. My car slowed down so i pulled over and shut it mdown. Id thers iny major problems i should be concerned...


If u still have oil in the oil filter, the motor should be fine.While u have the pan off u should spin the motor to make shur there is nothing louse

May 28, 2012 | 2006 Chevrolet Cobalt LTZ

1 Answer

Will the oil pan from a 2.2 l chevy motor fit on a 2.0 l chevy motor?


There are probably lots of used oil pans in the salvage yards. The problem is that the salvage operators will only sell them with a used engine. That is why you are being told that there are none available.

To answer your question:
The part number for a 2002 Cavalier 2.2L OHV oil pan is 88890999.
The part number for a 2006 Chevrolet Cobalt SS 2.0L oil pan is 55558816.
So, the simple answer is NO, they are NOT interchangeable.

The good news is that you can order a NEW oil pan from gmpartsdirect.com for about 40% off of dealer MSRP. Click the link below to go there.
http://www.gmpartsdirect.com/results.cfm?partnumber=55558816

May 08, 2012 | 2006 Chevrolet Cobalt SS

1 Answer

How do i remove the oil pan on a 2005 chevrolet cobalt


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and support the vehicle.
  3. Drain the engine oil.
  4. Remove the engine drive belt.
  5. On the 2.0L engine, remove the intercooler pump bracket bolts from the oil pan.
  6. Remove the lower A/C compressor bolt from the oil pan.
  7. Remove the oil pan bolts.
  8. Remove the oil pan

Dec 29, 2011 | Chevrolet Cobalt Cars & Trucks

1 Answer

How do i remove 2008 cobalt oil pan?


  1. Raise and support the vehicle.
  2. Place a drain pan under the oil pan drain plug.
  3. Remove the oil pan drain plug.
  4. Drain the engine oil.
  5. Remove the engine belt
  6. Remove the lower AC compressor bolt.Remove the 4 oil pan to transaxle bolts (1).
  7. Remove the oil pan bolts.

Jun 17, 2011 | Chevrolet Cobalt Cars & Trucks

2 Answers

Can a good back yard mechanic replace the transmission oil pan on a 2008 Chevy Cobalt?


Yes it shouldn't be a problem but change the filter as well...........Hope this helps.

Sep 27, 2010 | 2008 Chevrolet Cobalt

1 Answer

2006 chevy cobalt LT. the key is stuck


Have you tried shifting the gears completely through and then putting the car in park. It sounds like the car isn't able to be put completely in park to release the key. Try putting the car in N and removing the key. Even thought the car may not completely be in park to release the key, The gear most likely is in park but not enough to make the switch/sensor to release.

Jul 16, 2010 | 2006 Chevrolet Cobalt

1 Answer

How do you take off the oil pan on a 2007 chevy cobalt? I have removed all the bolts that secure the oil pan, but it will not come off.


There is a gasket between the engine and the oil pan. It is probably stuck. You will have to pry it loose with a screwdriver. It may damage the gasket so you might have to get a new one. Make sure you scrape off the old gasket before installing the new one.

May 27, 2010 | 2007 Chevrolet Cobalt Coupe

1 Answer

I need bolt torque specs for a 2006 chevy cobalt Rod bolt and pan bolt torque specs also oil clearance for rod journals


if you just go to a mecanic and ask what are the specks on that they should know but i think if you just tighten them down with an impact wrench till it is really tight after ou start the car it will run like **** then it will work its self out

Nov 17, 2009 | 2006 Chevrolet Cobalt

1 Answer

My oil pan is cracked and I want to know if I have to remove the engine to change this.


If you can see and get to all of the bolts which hold the oil pan to the bottom of the engine and if it appears obvious that the oil pan can be removed without being blocked by anything else, then you don't have to remove the engine. Come to think of it, I don't think that I have ever seen a car where you had to remove the engine in order to remove the oil pan.

Apr 20, 2009 | 2005 Chevrolet Cobalt

Not finding what you are looking for?
2007 Chevrolet Cobalt Coupe Logo

Related Topics:

848 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...