Question about 2001 Chrysler Town & Country

Open Question

2004 chrysler sebring power steering hose diagram

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ga_drifter
  • 36 Answers

SOURCE: 2004 chrysler sebring.The driver side rear door electric window

you have a bad window regulator assembly

Posted on Jan 30, 2009

dsacco86
  • 1077 Answers

SOURCE: belt diagram for a 1999 chrysler sebring lx

I think this is the one:
74340f3.jpg

Posted on Mar 26, 2009

01fordeb
  • 1033 Answers

SOURCE: oil sending unit on 2004 chrysler sebring V6

Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Posted on Jan 03, 2010

  • 538 Answers

SOURCE: 2007 chrysler sebring serpentine belt diagram

Go to; daycoproducts.com, click cars and trucks, then go to serpentine belt. Then on the right side of the screen click on finding your vehicle. Then get the illistration number and click on illistrations, go to that number it should something 6-? or 7-?. It's a pretty good websight.

Posted on Jan 31, 2010

sandman357
  • 236 Answers

SOURCE: 2004 chrysler sebring idle speed is too slow. HOw

why do you want your rpms higher while idling? you don't want them high because your gas bill will reflect that. slow shouldn't matter but if it's dying while on idle it could either be your mass air flow sensor or your fuel filter being clogged

Posted on Mar 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the power steering pump on a 2004 Chrysler Sebring?


Here's a link to Autozone's repair guide on replacing your power steering pump SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Here's another link on bleeding it after you install new one and fill up with fluid. http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f802d6a47

Jul 15, 2015 | Chrysler Cars & Trucks

1 Answer

Belt diagram routing


go to www.automecanico.com translate this web with your browser
and get the topic.
God bless you

Jul 29, 2013 | 2008 Chrysler Sebring Convertible

1 Answer

Looking for a diagram for the hoses on a power steering for a 1998 chrysler Sebring convertable jx with the 2.5l motor


The pressure and return lines connect the pump to the rack and pinion which is what the tie rod ends are connected to.
If the pressure hose is disconnected from the rack, you should have a threaded hole in the rack near the steering shaft with nothing connected to it.
On some models there is a short hose and a pressure sensor in the line that connects to the line to the pump.
Is that what you are talking about ?

Sep 20, 2012 | Cars & Trucks

1 Answer

RED COLOUR OIL LEAKING FROM MY 2004 CHRYSLER SEEBRING CAR,WHAT SHUOLD I DO?


check the auto trans fluid level and the power steering fluid levels. If any are low, find the leak and have it repaired.

Dec 26, 2010 | 2004 Chrysler Sebring

1 Answer

2004 chrysler sebring the air bag light goes on and off while driving.


The clockspring (air bag wiring, under steering wheel) maybe be bad.

Jun 27, 2010 | 2004 Chrysler Sebring

1 Answer

How to install a power steering pump for a 1997 chrysler seabring conv


Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

May 13, 2010 | 1997 Chrysler Sebring

1 Answer

Power steering belt diagram for 2004 sebring 4 cyclinder


the diagram should be posted on the core support in front of the radiator or even under the hood of the vehicle have you looked to your owners Manuel as well however it should clearly be posted under the hood or on one of the strut towers along the side at some point

Sep 06, 2009 | 2004 Chrysler Sebring

1 Answer

2001 Chrysler Sebring- difficulty steering,


the belt will be on the front pulley on the power steering pump

Apr 22, 2009 | 2001 Chrysler Sebring

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...