Question about 1998 Chrysler Sebring

Open Question

Chrysler sebring windshield washer problems - 1998 Chrysler Sebring

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: Removing the windshield washer reservoir in a 2002 Chrysler T&C

REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove the engine fresh air housing inside the engine compartment.
  3. Disconnect the washer hose at the in-line connector forward of the cowl grille so that the in-line connector remains with the washer hose from the fresh air plenum.
  4. Disconnect the washer hose from the hose clip located on the front fender side shield.
  5. Remove the filler tube screw.
  6. Hoist and support vehicle on hoist or jack stands.
  7. Remove the right front wheel and tire assembly.
  8. Disconnect the left right front wheelhouse splash shield and move aside.
  9. Drain washer fluid from the reservoir and into a suitable clean container. This can be done by disconnecting the windshield washer hose from the front (outboard) washer pump and allowing the washer fluid to drain into a container through a temporary jumper hose connected to the front washer pump.
  10. Disconnect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the release position, then, depress the black tab and pull the connector off the pump or sensor.
  11. Remove the two reservoir mounting screws.
  12. Disconnect the reservoir from the body mount by raising the reservoir upward slightly and then down so that the reservoir filler neck and front washer hose pull through the opening in the front fender side shield.
INSTALLATION

  1. Push filler neck and front washer hose through the opening in the front fender side shield. Connect the reservoir to the body mount by lowering the reservoir down.
  2. Install the two reservoir mounting screws. Torque screws to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  3. Connect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the closed or locked position.
  4. Assure that washer is properly routed to prevent pinching and possible inoperative washers.
  5. Connect the left right front wheelhouse splash shield and move aside.
  6. Install the right front wheel and tire assembly.
  7. lower vehicle from hoist or jack stands.
  8. Install the filler tube screw. Torque screw to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  9. Connect the washer hose to the hose clip located on the front fender side shield.
  10. Connect the washer hose at the in-line connector forward of the cowl grille.
  11. Install the engine fresh air housing inside the engine compartment.
  12. Connect the battery negative cable.
  13. Verify system operation.

Posted on Apr 01, 2009

  • 5 Answers

SOURCE: I have a 2002 Chrysler Sebring LXI that the

first about your door lock control could make this problem, check the connection, for your washer look at the motor if its working it could be blocked washer lines

Posted on Jan 17, 2010

  • 1244 Answers

SOURCE: 2000 Chrysler Sebring windsheild washer pump

check the fuse panel for weak or blown fuse in the wiper/washer circuit if that all checks ok then using a test light or volt meter then find the washer pump leads at the bottom of the washer pump itself and with the circuit activated make sure you have 12 volts going to it also check the ground wire to it to insure proper ground if voltage is present then remove the motor assembly from the washer housing and relace the motor

Posted on Jan 23, 2010

Testimonial: "Quick, informatve response...perfect & thanks!"

leedavidian
  • 1420 Answers

SOURCE: Where is the windshield motor located on a 1998

Welcome to FixYa.com
Regards, Lee Davidian
a996b47.png

Posted on May 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Windshield wipers stop working when the defroster is on


The only thing they have in common is the ignition switch.

Dec 18, 2015 | 2007 Chrysler Sebring Sedan

1 Answer

2000 Chrysler Sebring windshield washer pump won't squirt n air pressured lines?


So your saying the fluid lines and fittings are not clogged, correct? Next, I have to check voltage and ground for washer pump. If your missing either one, have to track that circuit. Go from there.

The lite green wire at washer motor is voltage and the black wire is ground. If no voltage that will lead back to wiper/washer switch on steering column or the wiring circuit. If your going to work on steering column, make sure you disarm the air bag.

May 17, 2015 | 2000 Chrysler Sebring

1 Answer

Windshield washer doesnt have any pressure behind it, how to clean or unclog?


i know on GM models there is a little motor at the bottom of the reservoir, as you pull the lever you should hear the motor kick on. You can always used compressed air to see if there is any debri in the line.

Dec 11, 2012 | 2007 Chrysler Sebring Sedan

1 Answer

The windshield washer does not work, the wipers do,so the fuse should be good, help please


If you can here the motor working then your hoses are probably clogged. Easy solution is take the hose off the tank or motor. Use an air compressor to blow the line out. Please rate thank you!!

Sep 14, 2010 | 2006 Chrysler Sebring

1 Answer

2000 Chrysler Sebring windsheild washer pump


check the fuse panel for weak or blown fuse in the wiper/washer circuit if that all checks ok then using a test light or volt meter then find the washer pump leads at the bottom of the washer pump itself and with the circuit activated make sure you have 12 volts going to it also check the ground wire to it to insure proper ground if voltage is present then remove the motor assembly from the washer housing and relace the motor

Jan 23, 2010 | 2000 Chrysler Sebring

1 Answer

I have a 2002 Chrysler Sebring LXI that the automatic door lock inside on driver side quit working, but my remote unlock does work, and also, my windshield washer will not dispense, I have filled it up,...


first about your door lock control could make this problem, check the connection, for your washer look at the motor if its working it could be blocked washer lines

Jan 16, 2010 | 2002 Chrysler Sebring

1 Answer

WINDSHIELD WASHER FLUID


Could be that the line is clogged, or the spray nozzle itself is clogged up a bit. Begin by inserting a piece of fine wire into the nozzle, that may solve your problem.

Feb 23, 2009 | 1998 Chrysler Sebring

2 Answers

2002 Sebring wont start


sounds like fuses and relay problem

Dec 30, 2008 | 2001 Chrysler Sebring

Not finding what you are looking for?
1998 Chrysler Sebring Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...