Question about 1995 Buick Century

Open Question

Brake line routing 95 buick century

From master cylinder which port goes where?

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 169 Answers

SOURCE: horn relay 95 Buick century

It is located in the convenience center to the left of the steering column.

Posted on Aug 31, 2008

michigan man
  • 3533 Answers

SOURCE: 95 Buick Century dash removal?

you should not have to remove the dash to install a new radio all you have to do is remove the trim around the radio and then take out the bolts that hold the radio in and remove the wires from the back and also if there is a Walmart or Radio Shack near you get an installation kit and you plug it from the plugs from your old radio and it is alot easier to wire it that way

Posted on Mar 04, 2009

  • 335 Answers

SOURCE: need buick century egr diagram

If your car runs bad with an EGR code then I would suggest that the EGR valve be replaced. I would like to know what code was set on your computer. It would help greatly. When the EGR malfunctions, you will have rough idle and possible stalling. If you have a code indicating EGR it may also condem the cat converter.Please show any codes that are set. Thanks Moe

Posted on Apr 24, 2009

  • 208 Answers

SOURCE: 1987 Buick Century 2.5 serpentine belt diagram

call a parts store they usually can provide you the routing for serpantine belts good luck getting it right though it can be tricky pay close attention to how the belt is routed :)

Posted on Jun 22, 2009

  • 37 Answers

SOURCE: 1998 buick century cylinder 5 misfire

it sounds like you have low compression on cyl 5 might be bent valve.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Route for brake line to right front wheel from master cylinder on 1999 Buick centry v6_3100 3.1lL vin M sfi

The line should follow a line from the master cylinder along and thru the inner wing from there it connects to the flexi hose and onto the brake.

Mar 02, 2016 | Buick Cars & Trucks

1 Answer

How do you install a booster in a buick century 2004

Pull the brake master cylinder off, move it out of the way. Under the dash there are 4 nuts to remove behind the brake pedal. Pull the booster off and reinstall. You can move the master cylinder quite a bit. Just watch the brake lines.

Jul 19, 2015 | 2004 Buick Century

3 Answers

How do I flush out my brake system on a 1995 Buick century?

You are going to need one other person pumping the brakes

Jan 17, 2015 | 1995 Buick Century

2 Answers

1999 buick century brake pedal goes to floor-put new master cylinder on and blead both brake lines and master cylinder and pedal still goes to floor

Sounds like you may have a hydraulic leak somewhere. Check the rear wheel cylinders and front brake hoses going to the calipers.

Jan 26, 2012 | 1999 Buick Century

1 Answer

How do I bleed the brakes on a 98 buick century

start at the closest wheel to the brake master cylinder, you will need someone to pump the brake pedal to build up pressure then hold it down while you release the bleed nipple on the wheel brake cylinder then push the pedal to the floor to release the air & keep it down until you tighten the bleed screw then release the pedal & repeat the process on each wheel from front to back making shore that all the air is out of the lines DO NOT let the brake master run out of brake fluid ( keep topping it up)......hope this helps.....cheers.

Aug 17, 2011 | 1998 Buick Century

1 Answer

On the Master cylinder, which line goes to the front and which goes to the back (ABS Brakes)

Since the front supplies over 65% of the braking power, typically the front line ( closest to the radiator) is for the back and the back line is for the front. Master cylinders work in a reverse order; as the pressure is applied from the back to the front, the back activates the front brakes and vice versa.
Hope this helps!

Nov 15, 2010 | 1998 Buick Century

1 Answer

How to replace master cylinder on 1989 century

You have to Remove the brake lines going to the cylinder, then remove the 2 nuts holding it to the brake booster.

Make sure u bench bleed the new master before you install, the new one should come with a bench bleed kit, u must attach the 2 hoses to both ports on the master cylinder where the brake lines connect to, then run the 2 hoses into the top of the reservor and fill it with fluid, use a screw driver and pump the master cylinder until you can see no air bubbles running through the hoses

Apr 08, 2010 | 1989 Buick Century

1 Answer

Rear brakes are locked up in my driveway I cant backup, car has 97000 miles its a 2002 buick century


Aug 01, 2009 | 2002 Buick Century

1 Answer


Is there any fluid in the master cylinder? If no, fill it up and check for leaks.

Apr 05, 2009 | 1995 Buick Century

Not finding what you are looking for?
1995 Buick Century Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides