Question about Cars & Trucks

Open Question

Timeing mark to change swift diseal engine timeing chain

I need to find the cam and crank mark to lock and change timeing chain of maruti swift diseal

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

psds4
  • 293 Answers

SOURCE: timing marks,cam and crank,2.4l

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018d02c

Posted on Oct 09, 2008

  • 137 Answers

SOURCE: NEED TIMING MARKS 2.0L DUAL CAM FORD CONTOUR

the cam marks are on the cams under the valvecover the crank has a mark o nthe timing cover that you need to line it up to

Posted on Jan 20, 2009

  • 186 Answers

SOURCE: changed timing chain and need to align to cam with the crang

Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

Posted on May 22, 2009

kennyz195
  • 61 Answers

SOURCE: 1999 Ford Expedition 5.4L Timing chain setup

.

  1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Remove the crankshaft sensor ring from the crankshaft.
    a0044041.gif
  1. Rotate the crankshaft until the timing mark on the RH camshaft sprocket is approximately at the 11 o'clock position and the timing mark on the LH camshaft sprocket is approximately at the 12 o'clock position.
    a0049532.gif
  1. Using the special tool, position the crankshaft as shown.
    a0041102.gif
  1. Install the special tool.
    aa5423a.gif
  1. NOTE: LH shown; RH similar.
    Remove the two bolts, the timing chain tensioner and tensioner arm.
    aa5952a.gif
  1. Remove the LH and RH timing chains and the crankshaft sprockets.
    • Remove the special tool from the crankshaft.
    • Remove the timing chains from the camshaft sprockets.
    • Remove the right and left timing chains and the crankshaft sprocket from the crankshaft.
    a0029151.gif
  1. ani_caut.gif CAUTION: The bolts are different lengths and must be returned to their original location.
    NOTE: LH shown; RH similar.
    Remove the bolts and the timing chain guides.
    a0044040.gif
Installation
  1. ani_caut.gif CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    ani_caut.gif CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    Compress the tensioner plunger, using an edge of a vise.
    da0605a.gif
  1. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    da0606a.gif
  1. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    da0607a.gif
  1. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.
    a26917a.gif
  1. Remove the tensioner from the vise.
  1. NOTE: There are 61 links in the timing chain.
    If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.
    a0038720.gif
  1. Install the timing chain guides.
    a0044063.gif
  1. Using the special tool, verify correct crankshaft position.
    • Remove the special tool.
    a0041102.gif
  1. NOTE: Crankshaft sprockets are identical. They can only be installed one way. Refer to the following illustration for correct crankshaft sprocket installation.
    If removed, install LH and RH crankshaft sprockets.
    a14824b.gif
  1. Install the LH timing chain onto the crankshaft sprocket, aligning the one copper (marked) link on the timing chain with the slot on the crankshaft sprocket.
    a0041197.gif
  1. Position the LH timing chain on the camshaft sprocket with the two copper (marked) chain links and the camshaft sprocket timing mark aligned.
    a0049191.gif
  1. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    a0041196.gif
  1. Position the RH timing chain on the camshaft sprocket. Make sure the two copper (marked) links align with the camshaft sprocket timing mark.
    a0041104.gif
  1. NOTE: LH shown; RH similar.
    Position the tensioner arms and tensioners, and install the bolts.
    aa5952a.gif
  1. Remove the tensioner retaining clip.
    a26273a.gif
  1. As a post-check, verify correct alignment of all timing marks.
    a0041106.gif
  1. Remove the special tool.
    aa5423a.gif
  1. Position the crankshaft sensor ring on the crankshaft.
    a0044041.gif
  1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.


2010&c18=modelyear&c20=n310677&c35=wsm%2ctiming%20drive%20components%2csxj%2c303-01b%2cin-vehicle%20repair&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Posted on Apr 07, 2010

  • 1757 Answers

SOURCE: timing marks on twin overhead cams 2.4 and crank mark.

Click on the following direct, Free Link. It has several Diagrams including the Timing Belt + Marks for your 2004 Hyundai Sonata 2.4L DOHC In-Line 4-Cylinder Engine (located on the bottom half of the Page on the Link). There are additional Diagrams that will prove to be helpful while you are doing this...

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/sonata/2004_hyundai_sonata_timing_belt_diagram_marks.htm

Posted on Apr 16, 2010

Testimonial: "tHANKS, tHIS WILL DO THE JOB."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instruction changing timing belt 1979 Alfa Romeo Spider Veloz?


With Cam Caps loosened, FIRST loosen timing chain tensioner, press it in to loosen tension, Crank using ratchet to TDC (Top Dead Center on crank pully, (to keep from damage to pistons), align Exhaust Cam Timing Mark to mark on #1 Exhaust cam cover, then take up slack between Exhaust & Intake Cams (on top between the cams), Then align the Intake Cam to mark on #1 Cam Cap, "Now" loosen the 17mm bolt to tighten timing chain, rotate engine using rachet two times, reset TDC at the crank, and look at "Cam Timing Marks on both the Exhaust, and Intake Cams. If you did all this correctly the "Timing Marks" should be lined up so TDC,Exhaust, and Intake marks are all the same.

Oct 10, 2014 | 1979 Alfa Romeo

2 Answers

Diagram for engine timing for a 3100 Chevy V6


It's on TDC so align marks on cam shaft and crank shaft with center of cam & crank shafts and the ECM will go from there. so you will have to change the timing chain if its loose or worn out.

May 08, 2014 | 1997 Chevrolet Monte Carlo

1 Answer

Timing mark


2.2 engine crank lock on left side but you have to remove block cap, both cam lock back side or keep crank key up and both cam slot in --- --- this way

Mar 04, 2014 | 2011 Mahindra Scorpio

1 Answer

Timing mark of suzuki engine m13a twincam fitted with timing chain


non stock? if not stock, say so , 1st thing.
post a question , you state only nouns.
all engines (gas) have 2 timings
1: spark
2: cam.
what is your question.?
my guess is you are not in uSA? state location.
used on swifts or jimny.
year?

chain marks. spark marks or crank pulley marks.
4th google hit. huge 1.3 PDF, id bet its there...
http://www.google.com/url?sa=t&rct=j&q=suzuki%20m13%20timing&source=web&cd=4&cad=rja&ved=0CDoQFjAD&url=http%3A%2F%2Fwww.vems.hu%2Ffiles%2FFero%2Fsuzuki%2520VVT%2F4.pdf&ei=pHIwUtf7AeHg2AWi_IHQBg&usg=AFQjCNGAIMvbaLlj5qu5g-_MnFOcSRDtaA


m13 is not easy find, information.... but google will find it if you just use it. I promise.
Alldata.com dont cover it.

Sep 05, 2013 | Suzuki Vitara Cars & Trucks

1 Answer

Changing timeing chain


dont try urself.get an expert

Jan 10, 2013 | Maruti Cars & Trucks

1 Answer

I need a picture of the timing marks for Jeep 4.0


Timing the Cam to the Crank

There are several ways to time the cam to the crank. Be sure to check the manual before you install the timing chain or belt.

  • Some timing sprockets are properly timed when the marks face each other.
  • On others, there must be a certain number of chain links between the marks.
  • Sometimes chains have colored links that must be aligned with the marks on the sprockets.
  • Some overhead cams have a mark on the cam gear that lines up with a mark on the cylinder head when the timing mark on the damper is at the TDC mark.
Align the timing marks for the camshaft and crankshaft sprockets before removing the timing belt or chain.

If the old parts are available, carefully compare the new gears or sprockets with the old ones. Check the keyway and timing marks just in case there might have been an error made in manufacturing. Sprockets are sometimes stamped backward. Its much better to find the problem during assembly, rather than waiting until problems show up after reassembly and reinstallation.

Maintaining Valve Timing

During a valve job, it is essential to keep the timing chain or belt in place to maintain correct valve timing. Position the number one cylinder at TDC. Some overhead cam engines use a single long chain for a cam drive. The chain can be wedged against its guides with a tapered block of wood.
the chain tensioner on some ohc engines must be wedged to keep the chain in position during cylinder head removal. courtesy of nissan motors.

Some engines have a lower and upper chain. These engines do not require special attention to wedging the chain. Be sure to look for hidden head bolts and check the repair manual before removing the OHC head.

Dec 07, 2012 | 1989 Jeep Cherokee

1 Answer

How do i set the valve timing if i cant see the timing marks on a VW 1.8 20valve golf cylinder head timing chain , i can only find the one on the belt side i have put the cam on TDC for the ex-valve but...


The 2 cams are linked with a chain at the rear of the cylinder head.

The cams need to be set so the slots on the chain sprockets line up with the cam tower caps with 16 links between cam caps.

You cannot see the front crank pulley tdc mark so you need to lock the engine at tdc with a screwdriver jammed into the timing hole on the bell housing after setting engine at tdc or use a DTI
to check to tdc in the #1 spark plug hole.

If the cams have not been disturbed you only need to set the belt cam sprocket to the mark and crank to tdc.....all this means pulling the core support into the service position so the belt tensioner can be locked down and/or doing a complete belt job along with a coolant pump if over 70,000 miles..

Aug 20, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

I have done engine overhall for my mazda 6 2003.i want to know how set timing and the timing marks?


there are special tools pin to lock crank in correct position and cams have flat plate that goes across into both at rear of cams small section goes up from memory, the cam gears have no dowel pin/locating pin to camshaft you do bolts up last when all are locked in position and grenade pin (locking)pin in tensioner is removed and chain is tight then hold cams with shifter or spanner(wrench) on cam flats and do up cam gear to camshaft bolts on each cam.
hole in front cover just above crank pulley at 11O clock, blind blanking plug must be removed to put in chain tensioner pin, crank blanking plug on your left side when looking at crank pulley(side of block) remove and locking pin goes into there when at TDC no1. and cams should be in position to lock with plate as described above.may not be any timming marks on chains or gears due to the locking tools needed and relied on for correct position.
good luck if you feel confident.
some Mazda dealerships may lend tools if you ask nicely or know some one.

Mar 10, 2011 | 2003 Mazda Mazda6

1 Answer

Changed timing chain and need to align to cam with the crang


Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

May 22, 2009 | 1995 Saturn Sl

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...