Question about 2007 Pontiac G6 GT Convertible

1 Answer

Broken driver's seat G6 2007

The drivers seat tends to lean to the right when elevated

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Ours finally brok and had to remove it to get it welded... weird flaw

Posted on Feb 16, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Can I replace my 98 grand prix driver's seat with

You can replace it as long as the one you are replacing is the same set-up. If you have a manual adjusting seat and replace it with a power seat it will fit but you wont have the hook ups for it. Also make sure if it is a bucket seat (single person) you dont replace it with a bench (3 persons fit in front) seat or you will run into problems with the center console and shifter. vice versa may bolt up but there will be a gap between the 2 front seats

Posted on Dec 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the drivers seat in my 2001 Cobra? It leans to the right and will not sit up straight?


Sounds like it could be worn out foam, springs, or a bent seat bracket. I'd take it to a shop and get a free estimate. They'll be able to point you in the right direction.

Feb 20, 2015 | Seat Cars & Trucks

2 Answers

The driver seat on my 2001 Toyoto Corolla leans back too much. I'd like to sit a bit more upright while driving, and so it's uncomfortable. The passenger seat is a lot better. I took it to a


You make up seat back stops out of some type
of hard plastic to move the seat back forward

If you have no stops on each corner, then the seat
comes out,upholstory off & some TIG Welding takes
place to modify to your likeing

You could shim the rear mounting brackets
on the floor but that is sort of crude & the bottom
cushion will feel odd

Mar 02, 2013 | 2001 Toyota Corolla

1 Answer

The driver's seat is broken in my Honda civic DX Coupe, how do I go about replacing it?


There's a bolt in each corner of the seat frame that goes thru the frame and into the floorboard. Remove these bolts, disconnect any wires, and pull the seat out. Same with the passenger seat if you want to put it on the driver side temporarily. The seat movement control will be on the inside though when you do this. Not a good idea, bit it can be done. Same seats, different actuator lever position.

Aug 17, 2017 | Honda Civic Cars & Trucks

2 Answers

2004 Malibu with broken weld on seat motor


you will have to replace the complete assy. the cheapest way is look for a complete wrecking yard seat, or have yours welded at a local machine shop

Jan 08, 2010 | 2004 Chevrolet Malibu

1 Answer

My driver seat on my 98 Toyota Camry keeps leaning back. It's not powered, its manual. I guess when I was leaning back to get my wallet out of my pants, I leaned back to hard and now it doesn't go back...


You have a broken seat frame.
You are going to have to have the seat removed form the car, the upholstry removed, and the broken metal frame re-welded. As to the costs, I would expect about $125-150 dollars.

Oct 12, 2009 | 1998 Toyota Camry

1 Answer

1993 5.0 convertable. Drivers seat leans back on in board side. removed from car and could not find any broken parts. losened covers and inspeced frame aswell.


See if floor pan is cracked,seat frames do crack on these, inspect better around welds and riveted areas. see back rest frame too for cracks

Jul 14, 2009 | 1993 Ford Mustang

1 Answer

Driver side front seat back bends


The seat back frame is broken, in most cases it can be welded but all the trim must be removed and the seat dis-assembled down to just the frame, any upholstery shop can do this job for u, about $100-200

Dec 02, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2007 Pontiac G6 GT Convertible Logo

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...