Question about 2000 Ford Taurus
Where is the fuel pump relay located
Fuel Pump Relay is usually located in the engine compartment (under the hood) fuse/relay box. But, if you are having problems starting the car,....there is most likely a fuel shut off reset button in the trunk, on the right side, under the carpeting, on top of the rear wheel well. Look around in there. That's where it was in my 1999 Taurus.
Posted on Jan 10, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: fuel pump relay
I was just looking for another fuse and came across this diagram and it shows every fuse and relay and where it goes. The Fuel Pump Relay is in the O slot in the fuse box under the hood which is located near the battery. it is a 20 amp mini fuse. Hope this helps, i saved the link for future use if i need it, might be a good idea for you too. Good Luck here is the link.....
Posted on Jun 18, 2009
SOURCE: Where is the fuel pump
The fuel pump relay is integral to the Central Junction Box ( CJB ) and is not serviceable Applies to, but not limited to the following models: Expedition / Navigator -- 2003 - 2006 Excursion -- 2002 - 2005 F-Super Duty 250-550 -- 2002 - 2007
Good Day!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.
Posted on Feb 15, 2011
If it's the 3.0L Vulcan Engine (OHV), the thermostat is on the driver's side of the vehicle. Follow the upper radiator hose back to a metal area with three 10mm bolts. This is the thermostat housing. Undo the bolts, and there's the thermostat. Mark the back of it with the old thermostat in it (if you get one with a jiggle valve, it'll make it easier to put the new one in because the jiggle valve needs to be on top). The thermostat and housing aren't perfectly round, so you'll have to play with it a little to get it to line up. Make sure to change the gasket. The spring side of the thermostat goes into the engine.
The water pump is in the serpentine assembly. It's the larger pulley located toward the firewall. It'll be easiest to remove the water pump if you also remove the coolant recovery tank. The water pump pulley has four 1/2" bolts that you need to take out WITH THE BELT STILL ATTACHED. I can't stress this enough. The belt will keep the pulley in place so that you can remove the bolts. Take the pulley off, then the belt. Remove the heater hose at the top and the radiator hose at the bottom. There are 12 bolts of two diameters (1/2" and 10mm if I'm not mistaken). Tap the heater hose lightly with a soft-faced mallet to break the seal with the gasket. Trash the old gasket. Replace gasket (you can also line the mating surface of the water pump with RTV Sealant, put the new gasket on the new pump, and line the other side of gasket with a second coat of RTV sealant if you want a really good seal). Install the water pump and torque to manufacturer's specs. Attach the pulley to the water pump hand tight and put the belt back on. Tighten the pulley bolts. Put the coolant recovery tank back in place. Fill with coolant, start engine, bleed and check for leaks.
To bleed cooling system: Idle the engine until the thermostat opens (you'll be able to tell bacause the upper radiator hose will be uber hot and you'll feel coolant running through this hose). Squeeze all hoses in the system that you can reach, but don't burn yourself. Stop the engine and let it cool. Open the radiator cap and squeeze the COLD upper radiator hose. You'll see some bubbles in your recovery tank. You might have to monitor your coolant level for a couple of days while the final bits of air are purged through your radiator cap (that's why it's pressurized).
Hope this helps. It's not hard, but it took me quite awhile.
Posted on Jun 27, 2009
Tips for a great answer:
Jun 23, 2016 | Subaru Cars & Trucks
Mar 21, 2014 | Ford Taurus Cars & Trucks
Oct 23, 2012 | Cars & Trucks
Oct 06, 2012 | 2003 Kia Sorento
Mar 15, 2012 | Cars & Trucks
Feb 03, 2012 | 2000 Ford Taurus
Jan 26, 2012 | 1994 Toyota Corolla
The fuel pump shut-off switch is
located in the passenger's foot well,
by the kick panel.
Jul 19, 2011 | 2001 Ford Expedition
Apr 09, 2011 | 1997 Ford Taurus
Apr 07, 2011 | 2000 Ford Taurus
2,828 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: