Question about 2000 Ford Expedition

1 Answer

GEM module replacement

How can I find the directions to replace my GEM module and fuse box on my 2000 EB Ford Expedition? I don't have the money to take it to someone! Does it have to be reprogrammed by Ford after it is replaced?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try a salvage yard that has an expedition or an f150 pickup and take the parts off and install in yours disconnect the negative side of the battery and you shouldn't have to have it reprogrammed

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do i have to replace the fuse box when replacing the GEM module?


on ford trucks the gem module is part of the fuse box .Go to junkyard and buy and have dealer program if cost is to high from dealer

Jun 30, 2014 | 2002 Ford Excursion

1 Answer

Gem Module, Fuse Box and Window Reseal


This 1997 Ford F150 needs the GEM module changed due to multiple conditions. To see testing that lead to this repair please click here. The GEM module is located t the rear of the interior fuse box.
dsc02823.jpg
The first step is to remove the trim panel that covers the gap between the upper side of the steering column and the dash. It just unsnaps from the dash. It makes it a little easier to remove if you move the shifter all the way down to drive 1.
dsc02824.jpg
With that out of the way the lower dash cover can now be removed. Most of the screws have 7 mm heads but there are two that have 8 mm heads.
dsc02825.jpg
Those two are at the lower edge of the fuse box.
dsc02826.jpg
One wiring harness needs to be disconnected from the panel.
dsc02827.jpg
Now the screws for the fuse box can be removed.
dsc02828.jpg
The wiring harnesses can be removed from the back of the fuse box. Two 10 mm headed bolts at the center of each connector.
dsc02829.jpg

Next remove the tube brace from around the bottom of the steering column. Four fasteners with 13 mm heads.
dsc02830.jpg

Now wiggle, pry and twist the fuse box and GEM module assembly down.
dsc02831.jpg
After the assembly is down far enough unplug the remaining harness connectors from the GEM module.
dsc02832.jpg
Almost there.
dsc02837.jpg
The assembly is now free of the vehicle.
dsc02833.jpg
The GEM module is held to the back of the fuse box by three phillips headed screws.
dsc02834.jpg
Easy to remove Now.
dsc02836.jpg
With the three screws removed the GEM unplugs from the back of the fuse box.
dsc02835.jpg
I put it all back together and checked my repair for power to the driver's power window switch.
dsc02842.jpg

Jan 10, 2012 | 2000 Ford Expedition

1 Answer

G.E.M. on 2005 Expedition. Where is it?


it is the fuse box under the hood the bottom side is called the gem module

Dec 19, 2010 | 2005 Ford Expedition

1 Answer

My Ford 2000 Expedition eb will not start. I've replaced the battery starter still nothing just clicks.


my ford 2000 expedition eb will no start; batery ok starter ok selenoide ok

Jun 20, 2010 | 2000 Ford Expedition

1 Answer

What is the GEM module, how does it apply to the power locks, and how much do they cost? My power locks keep trying to lock and unlock on my 2000 Expedition. Saw a post that said that the GEM module needs...


before, you wamt to replace the module that you said. Can you try this simple thing ,check the power door lock relay. The lock relay block located behind the right side of the instrument . hope this can help.

May 07, 2010 | 2000 Ford Expedition

2 Answers

2000 Ford Focus automatic door locks quit working. Replaced Central locking module, but still does not work. All of the doors will only work manually. Remote works to open trunk only - will not work on...


check fuse 63 first.

Visual Inspection Chart Mechanical Electrical
  • Binding latch mechanisms
  • Binding linkage
  • Misaligned door
  • Central junction box fuse 63 (20A)
  • Damaged wiring harness
  • Loose or corroded connection(s)
  • Circuit
  • Door lock switch
  • Door lock actuator



It could also be your GEM (generic electronic module) which is expensive as it controls a lot of stuff. A scan tool can be used to cehck for fault codes from the GEM.

Jun 23, 2009 | 2000 Ford Focus

1 Answer

Interior light and diagnostic plug doesn't work


The data link gets it's power from fuse no. 3(20 amp) in the interior fuse panel,which also is the power for cig. lighter. This fuse gets it's power from fuse no. 103 in the battery junction box (50 amp).

For the interior lights the door adjar switches in the door send a signal to the GEM module.It then grounds the coil side of the interior lamp relay. The switch on the dash that you turn on manually also grounds the coil side of the interior lamp relay so that would mean that everyrhing after the GEM is ok.Are the lights not turning on from any door including the deck lid? If not then problem would have to be in the GEM module.

Feb 26, 2009 | 2000 Ford Expedition

1 Answer

Gem module 2000 expedition


Has water intruded into the module? if so yes

Sep 16, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

2,352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...