Question about 2003 Jeep Grand Cherokee

1 Answer

Transducer? i need to know the name of the part that the cam position sensor sits on?

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

THAT WOULD BE THE OIL PUMP DRIVE

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the function of the transducer? Stuck in "Limp In Mode"


A transducer is a sensor that does not need to make physical contact with what is is trying to sense. It can be used to detect the presence or position of something; on boats they are used to sense the distance to the bottom to determine the depth of the water.

These devices are typically employed to provide feedback - or "prove" that a command has completed or component is in the right place ie: A command to shift from position "A" to position "B" will be halted when the transducer at position "B" detects the presence of the shifter.

If the transducer is unable to detect the shifter at "B" or falsely detects that the shifter is always at "B" - it can cause problems. The device (computer or controller) that interprets the transducer output has no way of knowing if the shift has completed or not and can decide do something to limit damage to the motor, transmission, etc.

Here's a video that details the fix for your code on a Chevy Lumina
https://www.youtube.com/watch?v=NaLrsuRnLww

Dec 02, 2014 | Cars & Trucks

1 Answer

Where is my camshaft position sensor located on a 2008 chevy aveo


It should be located between the cam shafts. If you remove the Beauty Cover (( that's what they call the cover across the top of the motor. )) And then the Valve Cover. The Cam Sensor will be sitting between the Cam Shafts. Closer to the Intake Cam Shaft.

Aug 16, 2014 | Cars & Trucks

1 Answer

Camshaft sensor is chirpping


Hi, welcome to FixYa.com my name is Shawn and I will be answering your question.

It is not the cam sensor it is the cam syncronizer that needs to be replaced. That is the piece driven by the cam shaft that the cam sensor sits on.

I hope my assistance helped you and resolved your concern, if you need further assistance please ask.

Aug 07, 2011 | 2005 Ford Ranger

1 Answer

Need to know what dodge codes P0325, P0344 & P0340 mean


0325 knock sensor
0344 cam position sensor intermittent
0340 cam position sensor failure

I would replace the cam position sensor from the codes you provided. The knock sensor
would most likely be related to the sensor failure.

Jun 28, 2011 | Dodge Neon Cars & Trucks

1 Answer

I have a 1994 mercury grand marquis. it has several codes that come up when i pull them from the check engine light. what are these code meanings, and what needs to be done to fix them. any help would be...


I'm giving you these codes from a haynes manual,
326 EGR circuit voltage lower than expected

327 EGR valve pressure transducer/position sensor circuit below minimum voltage

332 EGR valve opening not detected

337 EGR valve pressure transducer/position sensor circuit above maximun voltage

Nov 28, 2010 | 1994 Mercury Grand Marquis

2 Answers

1998 dodge ram 2500 4x4 HD. randomly wont start. it only happens after sitting overnight, and once it occurs you must let it sit for day or two and she will start right up! it makes a very distinct...


HI I HAD SAME PROBLEM IT WAS THE COIL. IF YOU TAKE IT OFF THEN LOOK AT IT AND SEE IF IT IS CRACKED AT THE BOTTOM BOTH MY TRUCKS DID SAME AND COIL FIXED BOTH

Jan 17, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

I need to knwo where the cam position sensor is on


cam sensor is in the distributor. also know as the pick-up assembly.

Nov 10, 2009 | 1999 GMC Jimmy

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

1 Answer

Ineed to know the location of the cam sensor on a ford escape 2002 with the 3.0 liter V6 DOHC


SECTION 303-14: Electronic Engine Controls 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor —3.0L (4V) Removal and Installation
  1. Remove the camshaft position (CMP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Remove the sensor.
4544c22.gif
#56 is the cam sensor. please rate as fixed if this is what you need.

231ee68.gif

May 02, 2009 | Ford Escape Cars & Trucks

1 Answer

P0340 code in my Jeep Liberty 2002


Since a P0340 Could be either the Cam Position Sensor or The Crank Position Sensor they are obviously in 2 different spots, however they both either sit on the back of the engine or on the transmission bellhousing. Your Cam Sensor is at the top and your Crank Sensor is near the bottom.

Hope this gives you some direction. Thanks for using FixYa!

Sincerely,

JC

Nov 21, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2003 Jeep Grand Cherokee Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...