Question about 2006 Chevrolet Equinox

Open Question

P0727 p0335 intermittent no acceleration - 2006 Chevrolet Equinox

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix P0335 and P0727 error codes for Cadillac Catera 2000?


P0335 is a code for a faulty crank angle sensor. When this sensor starts going bad, usually the car will not start till it cools down, may cause rough running or no start at all. P0727 is a communication error between the engine control module and the transmission control module. Check for any bad connections between both modules.

Jul 22, 2016 | 2000 Cadillac Catera

1 Answer

What is code p0727


Possible causes
- Faulty Crankshaft Position (CKP) Sensor
- Crankshaft Position (CKP) Sensor harness is open or shorted
- Crankshaft Position (CKP) Sensor circuit poor electrical connection
- Communication error between the Engine Control Module (ECM) and Transmission Control Module (TCM)

The P0727 Codes is triggered when the TCM receives no signal from the ECM.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P0727 Description
The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM).


May 06, 2015 | Cars & Trucks

2 Answers

2000 volvo s40 p0335 and p0336 intermittently


both codes are for crank position sensor problems. Change it.

Aug 23, 2014 | 2000 Volvo S40

1 Answer

I found I have code P0335 P0335 Crankshaft Position Sensor A Circuit Malfunction My car has recently developed a problem where it doesn't start, and I hooked up a scanner and got that code. Would...


A P0335 "check engine light" code could be caused by:

  • Damaged CKP sensor connector
  • Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
  • Sensor output open
  • Sensor output shorted to ground
  • Sensor output shorted to voltage
  • Failed crank sensor
  • Broken timing belt
  • Failed PCM
  1. Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal.
  2. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs?
  3. If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay?
  4. If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

please check this maybe

Jan 12, 2011 | Infiniti QX56 Cars & Trucks

1 Answer

I have a codes P0073 P0339 and P0335 what a re each of them?


CODE POO73- OUT SIDE AIR TEMPERATURE SENSOR CODE PO339- CRANKSHAFT POSITION SENSOR CIRCUIT INTERMITTENT. CODE PO335 -CRANKSHAFT POSITION SENSOR CIRCUIT MALFUNCTION.

Jul 07, 2010 | Cars & Trucks

1 Answer

2002 Mitsubishi Galant 2.4 with repeating error codes P0335,P0340


Check your timing marks , you may have jump the tooth on a timing belt.

May 10, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

99 max no start p0335


The P0335 refers to the electrical circuit and not necessarily the sensor. Please see this article for full details - P0335.

Feb 06, 2010 | 1999 Nissan Maxima

1 Answer

Audi A6 RPM Signal from ECU


dont think you are reading the codes right because PO in front of the code is not a genuine Audi code ,well not according to my information ,try autozone who issue these codes or a snap on code reader booklet

Dec 26, 2009 | 2002 Audi A6

1 Answer

P0335


Hi, you can fix it by reading the article found here on P0335 - http://www.obd-codes.com/p0335

Mar 29, 2009 | 2003 Mazda Mazda6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...