Question about 2002 Daewoo Nubira

1 Answer

Trouble changing gears 1st and 2nd

When i try and select 1st and 2nd gear, i have to apply pressure as they are hard to get in and crunching. Ionly brought the car (daewoo matiz ) in december please help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Daewoo Master
  • 64,286 Answers

If the clutch feels firm with no play u may have worn syncronizer's in the trans, take it to trans shop and have them road test it, they will not charge in most cases.

Posted on Jan 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge Ram 3500 skips from 1st to 3rd gear, had rebuild after still the same issue. Any advice?


Governor pressure controls the 1st and 2nd shifts. After that is the 3 and 4 solenoids. you would need to look at the pressure when driving(takes a scanner). pressure is 20 to 30 PSI from 1st to 2nd, depends on acceleration. After that the pressure will jump to 100+ psi. Did you replace the governor solenoid and sensor? They are on the passenger side of the transmission and sit in a block that detaches from the valve body.

Sep 22, 2016 | 2005 Dodge Ram 3500

1 Answer

2008 toyota Camry manual hard shifting from 1st to 2nd gear


With the engine off see if the shift between 1st to 2nd feel,s free if not it could be the cable check the clutch is disengageing all the way it should go into reverse without crunching,other then that it could be a synchro ring worn check that the gearbox has the right oil in it.

Dec 20, 2015 | 2008 Toyota Camry

1 Answer

1986 dodge clutch trouble


redo assembly for clutch as the gears on put back right.

May 03, 2014 | 1986 Dodge Ram Wagon

1 Answer

Fiat seicento


The transmission needs work, possibly an overhaul.

Dec 03, 2013 | Cars & Trucks

2 Answers

2007 Dodge Ram 2500 Manual Transmission Trouble


Take it back

Did you not test it out--- before paying
& driving off?

Maybe the trans has some internal wear,
from the previous owners habits

Dec 08, 2012 | 2007 Dodge Ram 2500

1 Answer

60 series toyota cruiser has trouble changing gears only 1st 2nd gear auto


You have a stuck solenoid in the auto, The only way to fix it is to remove the solenoids and manually free them up, This means removing the oil and oil pan and removing the solenoids.

Mar 03, 2012 | Toyota LandCruiser Cars & Trucks

1 Answer

My 2004 audi s4 makes gronchy noise when i put it in to 2nd gear when cold whats causing it?


If I've understood your problem correctly.....when changing from 1st gear into second the box is giving a metal on metal crunching sound?
  • This would be the syncromesh ring which is not equalizing the speed correctly.
  • The problem usually happens when there is wear on the same part.
  • Check to make sure that the correct transmission fluid has been used in the box.
  • To alleviate the problem and delay the time when it will require attention, use the double de- clutch method of changing gears, especially when the transmission is cold.
  • The double de-clutch is carried out in the following way.
  1. When in gear and changing from 1st gear to 2nd, change into neutral and release the clutch and then depress again before selecting 2nd gear....It is not required to rev the engine in the neutral position when changing up....
  2. When changing down rev the engine when the shift lever is in neutral for each change.
You'll soon get the hang of it and stop the crunching sound, protecting the box at the same time....
Regards Johngee

Nov 13, 2010 | 2004 Audi S4

1 Answer

2nd gear crunch


first of all you shouldn't be reving that high to change gears. that's too high. secondly if it's grinding only during the change from 1st to 2nd gear you may have a problem with the gears not being aligned anymore...ie synchronizers worn out, bearings worn out, etc. take to reputable transmission shop to get it diagnosed and repaired. it sounds like the synchronizers are a problem there. and you may have metal in your fluid now that it's been grinding which will affect the rest of the transmission. if you are speed shifting as in racing, you are not doing your transmission any good. you probably don't have a transmission built to do that if it's the original factory tranny... meaning you did a major NO NO to your tranny and are tearing it up speed shifting when it isn't built for racing.

Oct 13, 2008 | Hyundai Motor 1996 Elantra

Not finding what you are looking for?
2002 Daewoo Nubira Logo

Related Topics:

501 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64286 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...