Question about Cars & Trucks

Open Question

Change battery in locknetics door lock - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change door lock fuses where is door lock fuses


Power Distribution Center *PDC* Located under hood in upper driver corner, fuse box and relay box. There might be a fuse box by the battery also,

recomend disconnect negative to battery, so accidently dont short any thing out

Mar 08, 2017 | Mitsubishi Colt Cars & Trucks

1 Answer

Where is fuse box on mitsubishi colt mirage 2005 model i want door lock fuses change


Power Distribution Center *PDC* Located under hood in upper driver corner, fuse box and relay box. There might be a fuse box by the battery also,

recomend disconnect negative to battery, so accidently dont short any thing out.

Mar 08, 2017 | Mitsubishi Colt Cars & Trucks

2 Answers

What causes a malfunction in power locks?


The power door locks are controlled by the BCM -body control module ! The door lock switch is an input to the BCM .
The BCM, upon receipt of a door lock switch lock or unlock signal, will switch the appropriate door lock actuator control circuits to battery positive voltage. The opposing side of the door lock actuators are connected to ground internally within the BCM through the other door lock actuator control circuit and the doors will lock or unlock appropriately.
First thing to do would be check power an ground circuits at the BCM ! Do you have any other systems not working -power windows etc...
The DR/LCK fuse supplies battery positive voltage to the I/P fuse block for the door lock system. The body control module (BCM) supplies and monitors a reference voltage to the door lock switch through the door lock switch lock/unlock signal circuit. The door lock switch also receives a constant ground source. If a door lock switch is placed in the lock position or unlock position, the reference voltage is taken directly to ground and the BCM detects the voltage drop on the signal circuit.
Should have BCM checked for stored DTC'S - diagnostic trouble codes !
Ignition ON, observe the scan tool Driver Door Lock Sw, Psgr Door Lock Sw, Driver Door Unlock Sw and Psgr Door Unlock Sw parameters while using the driver and passenger door lock switches. The parameters should change between Active and Inactive.
?‡'
If the values does not change between the commanded states, refer to Door Lock Switch Malfunction.

Command the driver door and passenger door lock actuators to LOCK and UNLOCK with the scan tool, the doors should LOCK and UNLOCK when changing between commanded states.
?‡'
If a door lock actuator does not perform the LOCK and UNLOCK functions, refer to Door Lock Malfunction


DTC B3130 00: All Door Unlock Circuit

DTC B3135 00: All Door Lock Circuit

Aug 09, 2015 | 2010 Chevrolet Impala

1 Answer

My automatic door lock upon exit feature is disabled after the battery was changed


Go thrue the vehicle menu there should be options in there to choose from.

Apr 29, 2017 | 2009 Infiniti M35

1 Answer

I lost the key to my door lock on my 1994 jeep grand cherokee laredo and my battery needs to be changed and I cant change the battery because I know if i disconnect the battery cabels it will lock down...


First of all, you can give the dealer your vin number and they can get the correct blank for your key. Remove one of the door locks by removing the door panel,lock rod and spring clip around the inside door lock. Take the blank and the lock cylinder to a locksmith and he can make you a new key.
As far as your battery is concerned, at your local parts house or Kragen auto store, pick up a device that plugs into your cig lighter that has a 9 volt battery on it. this will stop your after market alarm system from locking the doors. Jeeps did not come with that type of system from the factory.

Jul 26, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Remote no longer opens or locks doors. Inside manual lock does not open other doors either.


It sound like the battery has died and need replacing and them re setting to the car you key will only open the drivers door on some cars even with central locking. change the battery

Feb 20, 2011 | Hyundai Motor 2003 Elantra

2 Answers

Door lock won't function


If you cannot lock/unlock any doors at all, change the battery on your remote. If all the other doors work, but not the driver's door, there's a malfunctioning magnetic switch on the door.

Dec 05, 2009 | 2006 Scion tC

2 Answers

Doors locking while driving after battery changed


that's a safety feature.... not sure why it didn't work before.... there must be a way to shut it off but i'm uncertain how to do it for that car.

Robert

Apr 18, 2009 | 2000 Renault 181

1 Answer

The battery in my 2006 pontiac vibe went dead. I recharged it; however, the setting for the door locks changed. It now unlocks automatically when I turn the car off instead of when I put the car in park. I...


The 2006 Vibe no longer has that feature. It was discontinued after 2005. I have the 2005 so I know how to change it. If your 2006 is able to change then here are the directions from my 2005.
Programmable Automatic
Door Locks
If you have an automatic transaxle, your vehicle is equipped with an auto door lock/unlock feature which enables you to program your power door locks.
Your vehicle left the factory programmed to Mode 4.
The following is a list of the available programming options:
Mode 1: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. There is no automatic door unlocking.
Mode 2: No automatic door locking or unlocking.
Mode 3: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the shift lever is moved to PARK (P) with the ignition on.
Mode 4: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the ignition switch is turned from ON to ACC or to LOCK.
To change the mode you are in, do the following:
1. Set the interior lamp control dial to the door position.
See Interior Lamps Control on page 3-16.
2. Move the shift lever into PARK (P) and close all doors and liftgate.
3. Turn the ignition to ON.
4. Within five seconds after the ignition is turned to ON, press and hold the power door lock switch in
the lock position for about five seconds.
5. The interior lamp will flash to indicate that the mode has been changed. For example, if the lamp flashes once, the function has been changed to Mode 1.
If the battery is disconnected or run down, the mode is changed to the initial mode which is Mode 4.

Jan 22, 2009 | 2006 Pontiac Vibe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...