Question about 1991 Ford LTD Crown Victoria

Open Question

Need wiring diagram for 1991 crown victoria engine and electronic

Hi and thanks for being here. I need a wiring diagram for a 1991 crown victoria 4.6. I have looked every where even pub library and cannot find the proper one. there seems to be some controversy as to when or what year these were marketed.[or a half-year model]
tis is being installed in a 1946 lincoln. I have this thing firing, but no fuel injection. haynes and other cheap books are not working, show different color wiring etc, and no pin-outs.Im currently at a pub library, and could use some help. my home email is telecaster195196@peoplepc.com
if someone can help i would appreciate it.
thanks.
bob barnes, natalia tx

Posted by on

  • yadayada
    yadayada May 11, 2010

    suggest u go on ebay and try to find a used factory wiring diagram and troubleshooting booklet, they break down every circuit in the car into seperate diagrams, they are the best out there and at about $25-30 worth every dollar..

×

6 Suggested Answers

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

mindreader
  • 578 Answers

SOURCE: I need the fuse diagram for a 2001 crown victoria

go to
http://www.motorcraftservice.com/pubs/content/~WO1CRO/~MUS~LEN/41/01croog4e.pdf
and check out pages 156 - 161. They provide all you have asked for!

Posted on Oct 11, 2009

reisdos
  • 1297 Answers

SOURCE: fuse diagram for 2000 crown victoria

there are 5+ pages of fuses what specifically do you need


Posted on Jul 30, 2010

lbrown1806
  • 488 Answers

SOURCE: replace 2004 Crown Victoria headlight

From the engine compartment, unlock the 3 tabs that are over the headlight housing area. Remove the cover and unscrew the plastic ring that has the wires protruding from it. Carefully pulls the light fixture out of the housing. Pull the 2 L-shaped tabs up and remove the lens section. Reverse the steps to re-install the headlight. If replacing the full turn signal housing, unscrew 2 screws from each light , disconnect bulb wiring and remove. Replace accordingly.

Posted on Aug 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the pcv valve located on a 1991 ford crown victoria?


its located at the back of the engine near the firewall. it has a large hose connected to it(3/8") if I remember right. it is attached to top of the PCV valve. pull the hose off then you can pull the valve out of the rubber grommet that holds it into the engine.

Sep 23, 2014 | 1991 Ford LTD Crown Victoria

1 Answer

I need to know the wire diagram for my 1997 Crown Victoria because the wires are cross incorrectly


Sorry for the delay.
I am going back to answer you unanswered question.
You haven't stated what "wiring" diagram you need; however I am assuming it is for your Engine:-Spark Plugs, Wires and Coils.

Click on the following direct Link. It has the Spark Plugs, Wires and Coils - Diagrams for your specific vehicle.


http://autorepair.about.com/library/firing_orders/bl-fo-5268.htm

Mar 13, 2010 | 1997 Ford Crown Victoria

1 Answer

I need a wiring diagram for an 83 crown victoria starter coil


if you turn the key and the engine spins but doesnt fire try checking the timing for it to make spark at the time you need it to ,if it's out it wont catch and run or check for spark at the spark plug make sure it has spark use a dummy sparkplug in the boot and hold it on a ground and crank engine look for a blueish spark and if you have bare hands holding it you'll get a good jolt (insulated pliers)

Jan 03, 2009 | 1983 Ford Crown Victoria

Not finding what you are looking for?
1991 Ford LTD Crown Victoria Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...