- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
No you don't need any special tool . Find all screws on out side of door trim panel and the window handle , the mirror cover plate , then just pull on edge of the panel .
Gently pry the front side door trim panel (3) from the front side door by disengaging the plastic retainers which secure the panel.
Position the door trim panel (3) away from the door in order to gain access to the front side window switch electrical connector, if equipped.
Disconnect the window switch electrical connector, if equipped.
Remove the door trim panel (3) from the vehicle.
Remove the front side window switch from the door trim panel (3) by releasing the 4 plastic retaining tabs, as needed.
Use a cloth in order to pull off the snap ring which secures the front side door window regulator handle (1), if equipped.
Remove the window regulator handle (1), if equipped.
Remove the front side master window switch, if equipped. Refer to Power Accessory Switch Panel Replacement .
Remove the front side door inside handle (1). Refer to Front Side Door Inside Handle Replacement .
Remove the outside rearview mirror opening cover (2).
Remove the screw which secures the front side door pull handle (4).
Front Side Door Inside Handle Replacement
Remove the screw which secures the front side door inside handle (1).
Slide the inside handle (1) forward in order to release the retaining tabs which secure the handle to the door.
Open the front side door inside handle rod retainer and remove the front side door inside handle rod from the inside handle (1).
Remove the inside handle (1) from the vehicle.
For inside door handles, a special tool is required. It slips behind the door handle or window crank and moves the clip down so the handle will come off. For the outside door handle, Take the inside handles off using the special tool (available at any auto parts store). Remove the inside door panel. Remove the retainer clips for the door/lock linkage.The outer handle is held on by bolts on the inside of the door. Good luck
Remove front door handle bezel screw cover
Remove inside handle bezel screw
Remove inside handle bezel
Lift upward on the rear of the front door inside handle bezel
Disconnect electrical connector
Remove handle screw cover Remove handle screw
Remove door trim panel upper screw
Remove door trim panel lower screw
Remove door trim panel (pull the door trim panel outward to release the pin-type retainers)Remove front door sail panel Disconnect mirror electrical connector
Remove 3 exterior mirror nuts and exterior mirror
Jaguar 2000-06 - Locks & Lock Systems Power Door Locks - Removal & Installation
Door Lock Switch Door Lock Diagnosis & Testing
Visually inspect the following:
Misaligned door(s), hood or luggage compartment lid
Exterior door handle
Interior door handle
Door lock cylinder
Luggage compartment lid exterior release switch
Door lock actuator
Remote transmitter batteries
Door lock switch
Front electronic module
If an obvious cause for an observed or reported concern is found,
correct the cause (if possible) before proceeding to the next step.
Door Lock Motor Coupe And Convertible
Turn ignition key to position II.
Motor door glass to fully raised position.
Turn ignition key to position O.
Disconnect the negative battery cable.
Remove door casing for access.
Remove door water shedder.
Position PVC secondary water shedder for access.
Slacken and remove the door glass rear runner lower securing screws.
Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
Slacken and remove the upper securing screw and move the runner away from the glass.
Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
Slacken and remove the three latch assembly securing screws and position latch for access.
Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
Release operating cable from door handle. Move inner door handle
to the locked position. Remove operating cable outer abutment from
support bracket. Disconnect cable inner from door inner handle.
Remove lock motor assembly from door.
To install, reverse removal procedure.
Fig. Removing door lock actuator
Remove the door window glass
Detach the interior door handle.
Detach the actuator remote cable from the interior door handle.
Remove the interior door handle.
Detach the door window glass run.
Remove the exterior door handle retaining screws.
Remove the front door actuator retaining screws.
Reposition the front door actuator and exterior handle.
Remove the front door actuator and exterior handle.
Disconnect the front door actuator remote cable.
Detach the door lock cylinder connecting rod (1).
Detach the exterior door handle connecting rod (2).
Remove the front door trim panel.
Peel back the watershield.
Remove the exterior door handle access hole grommet from the door.
Loosen the screw.
The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw.
Remove the door lock cylinder bezel.
Slide the exterior door handle to release.
Remove the exterior door handle and gaskets.
Remove the front door speaker. For additional information, refer to Section 415-00.
Remove the speaker watershield.
Remove the 2 speaker standoffs.
If equipped, remove the window regulator handle.
Separate the handle cover from the handle.
Remove the screw.
Remove the window regulator handle.
Remove the spacer.
Remove the window control switch. For additional information, refer to Section 501-11.
Remove the bolt.
Remove the 2 front door lower bolts.
Remove the door handle cover plate.
Remove the 2 door handle screws.
Remove the front door handle.
Guide the door handle through the opening in the trim panel.
CAUTION: Do not pull directly outward on the front door trim panel, as damage may occur.
Remove the front door trim panel.
Lift upward to remove the front door trim panel.
To install, reverse the removal procedure.