Question about Cars & Trucks

Open Question

Ditec gate moor silver - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust open close limits on a 4 meter gate for a Germin motor


on the shaft that controls the arm or gear for the gate movement there will be 2 cams
open the gate and then loosen of one cam and adjust it off the micro switch until the gate is fully open
lightly tension the screw and then close the gate
repeat the adjusting on the second cam until the gate is fully closed
tension up the screw and then using the remote open the gate when it is fully open leave it or in it is not make small adjustment to get it open
press the remote to close the gate and again adjust to properly close the gate

May 02, 2018 | Cars & Trucks

1 Answer

Where is the program button located on moore matic x150.


If you mean the Moore-o-matic X150 garage door opener, it doesn't have a program button. It has three adjustment screws: Up limit and Down limit are on the downward side of the opener, the Door Pressure adjustment is on the back of the opener (lower left relative to the door operator terminals).

The manual for the Moore-o-matic X150 is available online from Manuals Lib, https://www.manualslib.com/manual/977303/Moore-O-Matic-X125.html#product-X150 , and liftmaster.com, https://www.liftmaster.com/catalogresourcesv3/en-us/shared/files/tucmanuals/a8448mm.pdf .

I hope this helps.

Cindy Wells

Dec 03, 2017 | Cars & Trucks

1 Answer

How do you open the lift gate wont work? I have a 2007 Acadia and there is no silver lever visible through the access hole. is there a way to mechanic a way to jumper it?


Has to have it .
Liftgate Trim Panel Plug
Procedure
From inside the vehicle lower the second and third, if applicable, row seats.
Use a small flat-bladed tool to remove the access plug from the liftgate lower interior trim panel.
Push on a silver lever located on the right just through the access hole to unlock the liftgate.
Open the liftgate from the outside of the vehicle using the exterior handle.

Outlook Traverse Acadia Enclave Lift Gate Won Open

Aug 24, 2017 | Cars & Trucks

1 Answer

Gate light on even when gate is closed


Open gate and find where the wiring enters the gate (bottom of door) pull back the rubber insulator and check for broken wires or wires touching each other.

Mar 05, 2013 | 2010 Jeep Liberty

1 Answer

2001 vovlo v7o xc trouble codes p0014 and p1237


DTC P1014 - B Camshaft Position - Timing Over-Advanced or System Performance (Bank 1).
At engine start-up the control module checks that the camshaft is in the correct position in relation to the crankshaft. Diagnostic trouble code (DTC) ECM-62 is stored if the control module detects the camshaft in an incorrect position on start up.

Possible source:
Camshaft cogs incorrectly seated
Incorrectly installed camshaft pulley
Contact resistance in the terminals.

Condition:
Malfunction indicator lamp (MIL) lit
The engine misfires.



DTC P1237 - Turbo Control Valve
Looks like the turbo is not producing enough boost. Check the waste gate hoses and the waste gate itself to see if its bound up. If the waste gate is working right, I would suspect a bad turbo.

This is an advanced level repair. You may want to have Volvo do the diagnostics on this one. Your code is for low turbo boost pressure. The waste gate is a big silver actuator on the turbo. It has vacuum hoses going to it. See if they are all hooked up. Also see if you can move the lever that the actuator pushes on. If its jammed that may be your problem.


Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.

Oct 31, 2011 | 2000 Volvo V70

1 Answer

I can't find a rental place to rent Kent Moore


I'd be willing to bet that a standard ball joint remover/installer would work on this application. Looks like a big "c" clamp with adapters to fit into place. A large screw aids in the install.

Jul 28, 2011 | 2003 Saturn L-Series

1 Answer

1985 Silver Spirit. Gates 7270 belt to smog pump. Will not go over fan blades. Which bolts to romove to remove fan?


hold fan belt with both hands as if stretching a rubber band.place one end of belt over a fan blade all the way down to the hub.loop the other end over as many blades as length allows.''leap frog'' over remaining blades as necessary.if that doesn't do,there should be 4 bolts holding fan hub to it's mount on water pump spindle

Sep 26, 2009 | 2006 Rolls Royce Rolls Royce Silver Spirit

1 Answer

Unable to program my new 2009 Altima Hybrid Homelink to my gate


The Learn Button is in a Silver little metal box that is in the opener housing but separate from the opener itself, pry off the case which kinda wraps around the reciever, it will say liftmaster of chamberlain the learn button will be in the reciever

Apr 05, 2009 | 2008 Nissan Altima Hybrid

1 Answer

Turbo 350 lock-up blowing fluid out of dipstick tube


Hi im matt in kc/ the vent on the top of the tranny got hot and is moore than likely plastic and is fused 2 gether just pop that thing out and it will work fine this happened two me already but with alot moore work hope that helps ya.

Mar 01, 2009 | 1985 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15387 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...