Question about 2005 Ford Focus

2 Answers

Replaceing a broken antenna mast on a 2005 Ford focus

I broke the antenna mast off of my 2005 Ford Focus I have bought the replacement parts but I need to know how to get the mount off to replace it as the stud that holds the mast broke off. I have the new base part.

Posted by on

  • 1 more comment 
  • Anonymous Jan 27, 2009

    Same Problem just need to know how to do it

  • softballtkl Feb 19, 2009

    I have the same problem. My antenna broke off and i have to replace everything, including the mast.

  • pandgchriste Mar 23, 2009

    Same problem. Ford said that they have to take off fender and splash guard to get to the parts. Its going to be $115.00 for half an hour and the $60.00 for the parts. What a rip off. Is this true, can't I get to the antenna through the interior light?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I am pretty sure if you remove the inside dome light cover and take out the light there is a bolt and nut under there for the base that you can unscrew. By the way where did you buy the parts from, Ford is telling me $70 for the antenna whip?

Posted on Feb 17, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You can buy the antenna at speedycarparts.com ($4.95 + s/h - $13.85 total).
I have also found it at ebay

Posted on Nov 11, 2009

  • luis fernando
    luis fernando Dec 24, 2013

    I need to fine a video on how to replace the antenna.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 model ford forte antenna removel


Power antennas require two people to replace. watch old mast as radio is turned on and off, then remove retainer nut and parts turn on and assist old mast out watching the teeth on plastic cable. fully extend new mast and lubricate with machine oil 3 and 1 works great feed new mask trying start teeth then turn radio off feeding into motor assembly install retainer parts and work antenna several time the overrun clutch will make final setting.

Nov 09, 2013 | Ford Cars & Trucks

3 Answers

How do you replace the atenna mast for 2005 sierra.


How do I install a new antenna on my GMC 05 2500 Sierra. I have to replace the base because it broke off. I've taken the dash off. But cannot seem to fish wire through the firewall.

Nov 26, 2010 | 2005 GMC Sierra

1 Answer

Replace antenna


Remove old Antenna
  1. Activate the antenna switch to the up position.
  2. Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
  3. Gain access to the underside of the area of the trunk where the antenna is located.
  4. Remove the bracket or brace that is below the hole and holding the antenna in place.
  5. Remove the mast.
  6. Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
  7. Remove the ground lead from the panel.
  8. Pull out the antenna coaxial cable.
  9. Unplug the coaxial from the extension coaxial cable.
  10. Remove the original antenna coaxial cable. Note the route the cable follows.

Install new Antenna
  1. Inspect the fender area where the antenna mast will be mounted for rust.
  2. Clean the area before installing the new antenna.
  3. Plug the new antenna coaxial cable to the extension coaxial cable.
  4. Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
  5. Connect the power lead of the antenna to the power antenna lead on the radio.
  6. Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
  7. Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
  8. Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
  9. Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
  10. Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
  11. Stop the motor after the cable goes into the housing 12 to 25 inches.
  12. Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
  13. Replace the retainer nut to the base of the antenna mast and secure tightly.
  14. Replace the panel that covers the antenna mount area.

Oct 16, 2009 | 1996 Honda Accord

1 Answer

Power antenna broke and I need to replace it. How


Buy replacement antenna mast. Remove old one by unscrewing the retaining cap nut. Turn on the radio & let the antenna cable run all the way up while you pull on it to remove it.
Install the new antenna mast by turning the radio 'off' so the spool inside goes back to its beginning while you feed the cable of the new antenna down into the antenna mast hole.
Once the cable is all the way down, reinstall the retaining nut/cap and turn on the radio to allow the spool to run the antenna 'UP.'... cycle the radio ON and then OFF several times allowing the antenna to move all the way up and all the way down.
That's it!

Sep 28, 2009 | 2001 Hyundai Sonata

1 Answer

How to replace thunderbird antenna


please rate service.

Automatic Electric Antenna
Removal
  1. Lower electric antenna (18850) .
  1. Remove rear retaining screws of RH front wheel splash shield for access to antenna lower retaining bolt.
  1. Remove lower retaining bolt.
  1. Remove radio antenna nut (18865) from top of motor tube and remove electric antenna through fender/splash shield access.
  1. Disconnect signal cable and motor wire connector(s).
Installation
  1. To install, reverse Removal procedure.
  1. Tighten top radio antenna nut to 6-8 Nm (54-70 lb-in).
  1. Tighten lower electric antenna retaining bolt to 5.8-7.8 Nm (51-69 lb-in).
  1. Check operation of electric antenna and radio chassis .

    Automatic Electric Antenna


    1faf511.gif

mast
Mast, Power NOTE: A power antenna mast which is bent or broken can be replaced without replacing the motor and tube assembly.
Removal
  1. Remove radio antenna nut (18865) and radio antenna stanchion (18919) .

    ssd~us~en~file=l6389b.gif~gen~ref.gif

  1. Loosen retaining nut inside tube using 14 mm (9/16 inch) socket, and slide nut part-way up mast.
  1. Raise antenna to run plastic drive wire at bottom of mast out of motor. Note direction of teeth on plastic drive wire.
  1. Saw off damaged portion of antenna mast. Remove burrs from mast and slide nut and contact tube off stationary tube.
Installation
  1. With the teeth on the plastic drive wire facing toward motor on antenna, push end of plastic drive wire of replacement mast assembly down into tube. Push it around curve at bottom of tube until end enters drive mechanism.
  1. Run motor down while pushing on plastic drive wire until about 305 mm (12 inch) of wire has been drawn into the tube. Stop motor and insert bottom of antenna mast into tube. Lower mast.
  1. Slide contact tube and radio antenna nut down antenna mast. Tighten nut to 0.45 Nm (4 lb-in).

  2. Raise and lower antenna several times to ensure proper operation.
651247a.gif

Jul 09, 2009 | 1995 Ford Thunderbird

1 Answer

Antenna mast broken


    Give these instructions a shot. Might be too generic but might be enough to get you going. Removing Original Antenna
  1. Step 1 Activate the antenna switch to the up position.
  2. Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
  3. Step 3 Gain access to the underside of the area where the antenna is located.
  4. Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place.
  5. Step 5 Remove the mast.
  6. Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
  7. Step 7 Remove the ground lead from the panel.
  8. Step 8 Pull out the antenna coaxial cable.
  9. Step 9 Unplug the coaxial from the extension coaxial cable.
  10. Step 10 Remove the original antenna coaxial cable. Note the route the cable follows.
    Installing the New Power Antenna
  11. Step 1 Inspect the fender area where the antenna mast will be mounted for rust.
  12. Step 2 Clean the area before installing the new antenna.
  13. Step 3 Plug the new antenna coaxial cable to the extension coaxial cable. (On some General Motors and Ford cars you may need an adapter to mate the 2 cables together. Car audio retail stores sell such an adapter.)
  14. Step 4 Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
  15. Step 5 Connect the power lead of the antenna to the power antenna lead on the radio.
  16. Step 6 Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
  17. Step 7 Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
  18. Step 8 Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
  19. Step 9 Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
  20. Step 10 Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
  21. Step 11 Stop the motor after the cable goes into the housing 12 to 25 inches.
  22. Step 12 Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
  23. Step 13 Replace the retainer nut to the base of the antenna mast and secure tightly.
  24. Step 14 Replace the panel that covers the antenna mount area.

May 13, 2009 | 1993 Chevrolet Corvette

1 Answer

2007 Ford Focus how to replace broken antenna


it unsrews

a4ba62a.gif
Antenna Base Removal
  1. Remove the antenna mast from the base.
unscrw counterclocwise
  1. Detach the interior light.
  1. Remove the interior lamp.
    • Disconnect the interior light electrical connector.
  1. Remove the interior lamp bezel.
  1. Remove the antenna cable/base retaining screw.
  1. Remove the antenna base.

Mar 14, 2009 | 2007 Ford Focus

1 Answer

2003 Ford Focus radio antenna broken off.


Should be a dome light in the interior that lines up with antennae on roof if it's same as I remember. Remove interior light and there should be screws in there holding base of antennae to roof. If it's just a broke off mast, try to unscrew stud from base & replace.

Jan 10, 2009 | 2003 Ford Focus

1 Answer

Antenna for 1997 jaguar xk8


There is a mast available, part number is lnc4134aa or lna4134aa, sorry but I am on holiday and dont recall the correct number.
You may have to remove the antenna and take it apart to retrieve the broken piece of mast, all basic stuff, really eaasy to do.

You can buy the mast aftermarket and on ebay for $25-$35, of pay the dealer $60+ for the same unit.
JPTCAT

Jul 02, 2008 | 1997 Jaguar XK8

Not finding what you are looking for?
2005 Ford Focus Logo

3,176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

67930 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Fordexpert

Level 3 Expert

5367 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...