Question about Cars & Trucks

Open Question

A have a 2001 ford excursion in a have a code 720 and 722 for transmission sensor i want to now the location

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75197 Answers

SOURCE: 1999 ford f350 engine code P0705 transmission range sensor warnin

P0705 - Trans Range Switch Circuit

Get under the truck and look where the trans shift linkage connects to the trans, there is a post that comes out of the trans, on that post u will see a large switch with multipile wires connected to it, that is the range selector switch, you need to remove the shift arm and a couple of bolts to remove the range switch, it is adjustable, u will see the slots, make sure u put the new switch in the same position as the old one or the truck may not start.

Posted on Jan 05, 2009

  • 1 Answer

SOURCE: transmission input speed sensor location

It is located on the front of the transmission. you will see 2 of them one on the left under small transmission lines it is the input then to the right behind the radiator overflow there is the other one. Easiest way to change them is with a 1" deep well socket

Posted on Jun 02, 2009

bschilz
  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

  • 6 Answers

SOURCE: Location of Speed Sensor 1998 Ford Explorer XLT

polarcycle is right but there is a speed sensor on the drivers side top of the trans. toward the tail shaft or transfer case. there is as well a sensor inside the trans. itself that is mounted on the web. behind the overdrive band and drum.

Posted on Jul 11, 2010

iambanshee74
  • 3489 Answers

SOURCE: Greetings, I have a 2001

Unfortunately there are several things that code could mean. Unless you still have the number code, it's hard to say. What is not hard to say is that, Ford should have caught that and addressed it in the immediate repair. Sounds like they got all the easy stuff in hopes that you would come back and spend more money. If there is a "check engine" light on, there is an issue and should be checked out and repaired. My first call would be to the Service manager of the dealer and kindly explain the issue that the technician MISSED. If he can't do anything, talk to the General manager. Let me know if you need anything else.

Posted on Oct 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Trans shifting hard into all gears


Have you hooked vehicle up to scanner to scan for codes? Sounds like a sensor,most likely the speed sensor on the transmission.Easy fix that you can do yourself,after acquiring the part.Not all codes will trigger a CEL take it somewhere and have them scan vehicle for pending and non-critical codes.

Nov 15, 2013 | 2001 Ford Excursion

1 Answer

2001 Excursion 6.8 V10, hard start, high idle, code P1288 KOEO, and KOER, no memory codes, with temp gauge in normal range scan data reads 20 deg F, suspect CHT sensors looking for sensor location.


CHT -cylinder head temperature sensor located under the intake manifold.you have to remove intake manifold to replace sensor its in the cylinder head.

Oct 22, 2013 | Ford Cars & Trucks

1 Answer

Transmission will not shift out of first gear into second gear without letting off the gas petal.


Hm. On the 2001 Excursion transmission, there is this problem with shifting into second gear.

OK.

Transmissions have sensors in them that detect speed and pressure inside the bell housing.

If one of the speed sensors is not working you might experience a no shift or late shift situation.

Also, if the sensor is good, but the passage ways are clogged with clutch material due to normal wear and tear, the transmission will experience late shifts or even no shift situations.

Have you had the transmission flushed and filled with new transmission fluid, lately?

If you haven't spend the $100 or so to have this service performed.
It's not a cure all, but sometimes it can help and is cheaper than getting your entire transmission rebuilt or replaced.

I would start there.

Good luck to you.

Jul 10, 2010 | 2001 Ford Excursion

1 Answer

Need 2002 ford excursion schematic transmission


See if these Helm diagrams are what you need.

0be6fb3.png

Mar 17, 2010 | 2002 Ford Excursion

1 Answer

Where do I find the factory code numbers for the keyless entry on a 2001 Ford Excursion?


They are on the keyless entry module. Some are located near the inside fuse box under the steering column. Others are located in the rear kick -panel where the jack is.

Nov 09, 2009 | 2001 Ford Excursion

1 Answer

Speedometer quit working on my 2003 ford excursion


Speed sensor located on the transmission must be replaced.

Sep 11, 2009 | 2003 Ford Excursion

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

2 Answers

2001 Excursion 7.3 diesel won't go into drive.


how is the transmission oil level is it filled to the proper level

have you ever replaced the filter in the transmission it may be full of clutch grime

Jul 27, 2009 | 2001 Ford Excursion

1 Answer

Check-engine light on


P1132 is front 02 bank 1 and P1152 is front 02 bank 2
This codes indicate a rich condition. I would check for a dirty air filter or a dirty MAF sensor.

Jan 31, 2009 | 2001 Ford Excursion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...