Question about 2002 Chrysler Sebring

Open Question

I have an 01 sebring with a 2.7l motor. it quit running, i pulled two codes codes are po725 and po700. i have replaced crankshaft sensor. i only get spark when camshaft sensor is unplugged

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: Crankshaft Position Sensor location 04 PT Cruiser

It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Posted on Feb 08, 2009

Ad
  • 15 Answers

SOURCE: 2002 pt cruiser Camshaft Sensor

change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Posted on Mar 04, 2009

csmock132
  • 4669 Answers

SOURCE: Crank sensor and camshaft sensor

The crank sensor is in the top of bell housing of the transmission towards the back of the engine compartment. The cam sensor is built into the distributor.

Posted on Mar 07, 2009

dsacco86
  • 1077 Answers

SOURCE: Code PO740 and PO700 show

Best to have a transmission place work on this.
Here are the meaning of the codes:
P0700 Transmission Control System Malfunction
P0740 Torque Converter Clutch Circuit Malfunction

It maybe cheap to fix like a bad sensor. Or it maybe something serious going on. Best to have a transmission shop check it out.
Good luck.

Posted on Apr 15, 2009

c17hydro
  • 2984 Answers

SOURCE: how can i replace the crankshaft position sensor

Fig. 2: Location of the crankshaft position sensor on 2.4L engines

fabab4c.jpg

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code po700 and po725 pops up on my 2001 chysler concorde what is it


P0700 is a transmission control system malfunction. And p0725 is a engine speed sensor malfunction.

Oct 07, 2017 | Cars & Trucks

1 Answer

I have a 2002 chrysler sebring shooting codes po700 po455 po442 po700 po841 po846 po732 gear2 inc ratio po731 inc ratio po733 pulled out solenoid and had a metal shaving on the magnetic end helpplease


P0700 Transmission Control System Malfunction P0445 Evaporative Emission Control System Purge Control Valve Circuit Shorted P0442 Evaporative Emission Control System leak Detected (small leak) P0841 Transmission Fluid Pressure Sensor/Switch A Circuit Range/Performance P0846 Transmission Fluid Pressure Sensor/Switch B Circuit Range/Performance P0732 Gear 2 Incorrect Ratio
Full list of the OBD2 DTC from P0700 to P0999

May 04, 2016 | Chrysler Cars & Trucks

1 Answer

I have a 2007 Chrysler Sebring 2.4 with code P0017. Replaced both camshaft sensors, didn't help. Car runs but it runs rough and stalls out. It's getting worse and worse. What could it be?


P0017 is a code for a bad CRANKSHAFT position sensor. Try replacing that. It will probably fix the problem. They go bad quite often.

Jul 01, 2015 | Chrysler Cars & Trucks

2 Answers

Code PO725


-Interpret the code before fix the problem. Look in its repair manual.

Mai

Apr 11, 2013 | 2008 Nissan Altima

1 Answer

Po725 code on chrysler sebring can it cause the starter to go bad


Hi there:

DTC P0725 - ENGINE SPEED SENSOR CIRCUIT


When Monitored: Continuously after a ignition key is turned from the OFF to RUN

position and/or key is turned from the CRANK to the RUN position.

Set Condition: The code is set when the engine speed sensed by the Transmission Control

Module (TCM) is different than the engine speed reported by the Powertrain Control

Module (PCM) over the Communication Buss.


POSSIBLE CAUSES:

CHECKING SYMPTOMS AND POSSIBLE CAUSES

LOW BATTERY VOLTAGE

BAD CONNECTIONS AT VARIOUS CONNECTORS

CRANK POSITION SENSOR SIGNAL OPEN

CRANKSHAFT POSITION SENSOR GROUND CIRCUIT OPEN

TCM CRANK POSITION SENSOR MONITORING DEFECTIVE



Hope this helps.

Mar 30, 2012 | 2001 Chrysler Sebring

2 Answers

2005 nissan almera,1.5letre.. fault code po725


P0725 NISSAN - Engine Speed Signal

The P0725 Codes is triggered when TCM does not receive the engine speed signal from ECM.

The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM).

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes:
- Open or shorted CKP sensor circuit condition
- Poor CKP sensor electrical connection
- Check communication error between the ECM and TCM
- Failed CKP Sensor

Possible solution:
Very common problem with Nissan vehicles, usually replacing the Crankshaft Position sensor takes care of the problem.

Keep us updated.

Feb 12, 2011 | 2005 Nissan Altima

3 Answers

Replaced crank sensor and now Im getting PO725 code.Would it be the camsensor that is giving me this code?


no, that code is for crank sensor:

Engine RPM input - circuit malfunction

Possible Causes: Wiring, CKP/RPM sensor, ECM/TCM

Oct 01, 2010 | Jeep Liberty Cars & Trucks

1 Answer

Codes


PO725 = Engine Speed Input Circuit
PO335= Crankshaft Position Sensor A Circuit

Apr 19, 2010 | 2002 Nissan Altima

2 Answers

My car was running poorly then 3 codes shoed PO320 PO700 PO725


Sounds like you have a transmission problem. Make sure the fluid is full. If you have neglected your transmission services, you will most likely need some trans work, which you will not be able to do on the side of the road.

Jun 04, 2009 | 2001 Dodge Durango

2 Answers

Dodge durango PO320 + PO700 + PO725


SYMPTOM
P0320 - NO CRANK REFERENCE SIGNAL AT PCM

WHEN MONITORED
With the ignition ON.

SET CONDITION
No signal from the Crankshaft Position Sensor is present during engine cranking, and at least 3 Camshaft Position Sensor signals have occurred.

POSSIBLE CAUSES
SYMPTOM
P0700 - EATX CONTROLLER DTC PRESENT

WHEN MONITORED
Ignition key ON, Continuously.

SET CONDITION
Any DTC sets in the Transmission Control Module.

POSSIBLE CAUSES

Jun 04, 2009 | 1997 Dodge Caravan

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...