Question about 1989 Suzuki Swift

1 Answer

Intermittent flashing on L or R turn or Hazard.

Have a new flasher unit to instal, cannot find the location of the old one. Where is it?

Vehicle is actually an Australian '89 Holden Barina but is just a rebadged Suzuki Swift

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 404 Answers

Hi Chalky!
I'm not familiar with your vehicle but if it were me I would put the Hazard Warning lights on and listen/feel the small relays/boxes close to the fuse board I'm sure you'll find it that way.
Good Luck!
Paul 'W'
Onyer~EDson(:0) {#><U.K.
Oh! please rate my effort.

Posted on Jan 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emergency flasher switch


The Hazard Warning flasher switch is located in the center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning flasher will continue to operate even though the ignition switch is OFF. NOTE: With extended use, the Hazard Warning flasher may wear down your battery. http://cdn.dealereprocess.com/cdn/servicemanuals/chrysler/2010-townandcountry.pdf

Nov 26, 2015 | 2010 Chrysler Town and Country

1 Answer

Location diagram for1996 chev blazer turn signal flasher unit


Flashers: The convenience center is used to centrally locate various buzzers, relays, flashers and/or circuit breakers. The turn signal and hazard flasher units are usually located in the convenience center located just below the instrument panel on the drivers side. Replace the flasher by unplugging the old one and plugging in the new one. Confirm proper flasher operation.

Hope helps.

Aug 16, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Turn signals dont work


For 1993 Oldsmobile Cutlass Ciera 3.3L FI OHV 6cyl. you have two flasher units, one for Hazard Light and one for Turn Signal...

The hazard flasher is located in the convenience center, under the dash, on the left side kick panel. The turn signal flasher is installed in a clamp attached to the base of the steering column support inside the car. In all cases, replacement is made by unplugging the old unit and plugging in a new one.

Hope this help (remember comment and rated this help).

May 12, 2010 | 1993 Oldsmobile Cutlass Ciera

3 Answers

My 2003 chevy impala turn signals won't blink. the lights come on but won't blink. I have checked the fuse. it looked fine.


Hi,

Your problem is your blinker or flasher, it is located under dash, behind the instrument panel right above the steering column. Cost is no more than $10.

If helpful, click below, GOOD LUCK

Apr 15, 2010 | 2003 Chevrolet Impala

1 Answer

99 ford contour hazard flasher unit where is it


Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)

e21631a.jpg

Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Pull the flasher from the back of the multi-function switch.

To install:
  1. Install a new flasher in the multi-function switch.
  2. Install the column shrouds.
  3. Connect the negative battery cable.

Hazard Warning Flasher
  1. Disconnect the negative battery cable.
  2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
  3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:
  1. Install a new flasher in the connector.
  2. Install the knee bolster panel.
  3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 02, 2010 | Ford Contour Cars & Trucks

2 Answers

Where is the turn signal\hazard flasher located?


it's in the auxiliary relay box behind the glove box.

13350 is base part number on flasher

Feb 03, 2010 | 2003 Ford F250 Super Duty Crew Cab

2 Answers

I have a 2001 chevy cav, and my turn signal are intermittent, the hazard lights work.. if its a relay switch were would be located?


Try the flasher unit inside the fuse box... I cant remember, but some cars have different unit for signals and hazard lights...

Jan 28, 2010 | 2001 Chevrolet Cavalier

1 Answer

Turn signals were intermittent and now will not


It is absolutely possible, and recalls are free. Take the free recall and hope it solves your issue!

Dec 10, 2009 | 2001 Oldsmobile Alero

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

2 Answers

Where is the flasher indicator unit located in a 1996 cutlass ciera


I just replaced the turn signal flasher today in my 1996 Olds Ciera. It was not near the steering column. It's actually behind the fuse box in the glove box but the easiest way to get to it is to remove the ashtray/cigarette lighter and it's harness and reach back to the right behind the fuse box. It took all of 10 minutes to replace. This is not the same as the hazard flasher, just the turn signal one.

Oct 21, 2009 | 1996 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
Cars & Trucks Logo

364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...