Question about 1999 Lexus Gs 300

Open Question

PROGRAMMING GARAGE DOOR REMOTE 99 LEXUS GS300

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Garage door opener on 2000 Lexus RX300

Check out the Homelink Website. I found instructions for my wife's GS300 there. I haven't tried it yet, so I'm not 100% sure this will work.

Posted on Jul 13, 2008

Ad
  • 1 Answer

SOURCE: 98 lexus gs300 codes p1120 p1121

I wanted to start a thread specifically about failures within the throttle body concerning the GS300 (1998 in my case)

My symptons were:
VSC, VSC OFF, and ENGINE Lights would come on, followed by my car going into Limp Mode, where only that last 25% (if that) of the throttle would respond (basically have to floor the pedal to even move at all).

During the mornings, or when the engine was COLD, the throttle operated normal...then once the car warmed up, usually at about 10 mins, the problem would start...it happened intermitantly at first...1 or 2 days over the course of a week, then it became more consitent, until last week it became a daily problem.

The first part I tried was the Throttle Position sensor, which is on the front side of the throttle body, and the easiest thing to replace...this didnt help at all. $300 part from Lexus, $80 part from RockAuto.com (exacly same part toyota OEM)

THE PART THAT FIXED THE PROBLEM:
===========================================
"Idle Valve Motor", which is the larger electrical object next to the TPS on my 98 GS300. Problem is solved.

The Codes I got were P1120 and P1121 - Accelerator Sensor problem. However it wasnt really the Accelerator Sensor, it was indeed to actual electrical Motor that controls the opening of the Butterfly valve inside the Throttle body.

I found the problem by good old trouble shooting, and using an ohm meter to see if the throttle electric motor was getting elev, I found that the elec motor just to the left of the TPS was basically freaking out and shutting down. The Accelerator Pedal Sensor is on the Back-side of the throttle body where the throttle cable connects to, and has a spring on it. It was fine.

GS300's are indeed "drive by wire" concerning the throttle...the cable triggers the Accel Pedal Sensor, which sends a signal to the ECU, the ECU then sends power to the Idel Valve Elec Motor (next to the TPS), which opens and closes the mechanical butterfly valve, then the TPS sensor detects how far the elec motor is actually opening the butterfly valve...its a closed-loop feed-back system, meaning any failure in any sensor will cause the entire systm to fail.

The throttle cable apparently is ONLY there to allow the fail-safe of having that last 10-25% throttle when the electronic system fails...there is a gearbox inside the throtle body which allows the tail end of the throttle to manually engage the butterfly valve...the rest of the time, the butterfly valve is 100% opened and closed via the idle control motor.

Posted on Jul 08, 2009

  • 2 Answers

SOURCE: Home link system will not accept garage door code.

I purchased a Chamberlain belt garage door opener. It was great! The lease on my duplex ended and the landlord bought it from me.

I found that the best way to program my vehicle's HomeLink buttons (to read the remote) was to do the learning procedure in a parking garage. This way the signal is not interrupted by all the waves around us.

Posted on Nov 11, 2009

swolfinor
  • 504 Answers

SOURCE: how do you program the garage door opener on the

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 26, 2010

swolfinor
  • 504 Answers

SOURCE: Programming car remote using garage door opener remote control fo

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program my garage remote in my 2003 es300 Lexus?


You probably need to program the garage door opener,not the car.I have only had to program the Craftsman opener in my garage once(our 2005 Grand Caravan has a built in opener)The opener should have a programming button(my Craftsman opener's button is under one of the light covers).It will probably have the programming instructions near the button(in TINY print).You will want to have ALL of your garage remotes handy(to make sure they all still work after adding the car's remote-some openers have a maximum number of transmitters allowed.

May 28, 2012 | 2003 Lexus ES 300

2 Answers

99 lexus gs 300 fuse box diagram


We do not have the owners manuals for any model of Lexus. they are not free to download, you must purchase them from Lexus/Toyota

Feb 24, 2012 | 1999 Lexus Gs 300

1 Answer

? can i program remot control for the garage dor


Make sure you have a fresh battery in the garage remote. Drive away about a block and park. Press the two outer buttons on the IS for about 20 seconds , they will flash 10-15 seconds and then go out,erasing any old codes in the car.
Then select a button position, 1-2-or3 on the car for your garage function. Hold your garage remote to the car's button pad and depress the garage remote button and the cars button (1-2 or3)continually. The LED in the cars touch pad will flash slow, then fast then go out. Once these steps are completed the car and your hand held are syncronized...thh car has recieved the remote function. That is step 1 for all vehicles.

Now you need to return to the garage and "introduce" your car to the garage door opener's receiver. Depending on the brand there will be a "learn" button on the garage door opener. You will climb a ladder and push the learn button as per instructions in the opener manual or on the stickers on the opener motor itself, if it is a Chamberlain, Liftmaster or Craftsman....
These buttons will be pressed to erase old opener codes or program to add new devices...which is what your car is.
Each opener has its own series of functions but generally after initial set up of the ceiling unit, you will depress the learn button and hold for several seconds. Then within 30 seconds , you will depress the cars button for about 2 seconds and release, the lights will flash on the ceiling unit in the garage indicating success and the next time you press the cars button the system works.
For complete detailed instructions go to the HOMELINK web site. It covers most cars by model and openers by brand with VERY detailed instructions.
Nice car! Enjoy and post back with results



Jan 30, 2010 | 2004 Lexus IS 300

1 Answer

I have a got a 1996 lexus gs300. I need to


This is normally done at the dealership. You will need the original master key, your new key and the car

Oct 11, 2009 | 1996 Lexus ES 300

1 Answer

Programming car remote using garage door opener remote control fo


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Jul 03, 2009 | 2003 Lexus ES 300

1 Answer

Program garage door opener in 2005 rx 330


There are 3 programmable Homelink buttons you can use for different remotes. Just to the right of the buttons there is an indicator light.

Decide which button you want to program. Point the none battery end of your remote 1"-3" away from the Homelink panel and press both the remote and desired Homelink button down and hold them down at the same time. After about 20 seconds, the Homelink indicator light will change from a slow flashing to a rapid flashing. You can then release both buttons,
If the garage door responds to the Homelink, your done! If not, your garage door uses a rolling codes transmitter and must be trained.
Find the training button on your garage door opener's transmitter (usually mounted on the ceiling). Press the training button and within 30 seconds press and release the programmed Homelink button twice. If the garage door opener operates, you're done! If not, press and release the Homelink button a third time and the garage door should respond. If it still does not, you may have a very old garage door opener with a none digital transmitter (like I did). In that case, you either need to buy a new opener or try to replace the transmitter with a modern digital unit (as I did). Advantage: cheaper than a whole new garage door opener.
Disadvantage: The newer openers incorporate safety features that my old opener does not have.

Apr 16, 2009 | 2005 Lexus RX330

1 Answer

The buttons for garage will not program in my Lexus RX 330 2004


The buttons inside the vehicle are syncronized/programmed with the operatus that physically opens and closes your garage door, not the operner... The garage door opener needs to have a "programming" feature switch that must be set to "programming" before you can program the buttons inside the car...

There are step by step instructions in your owners manual... This could be a 2 person operation...

I have a 2004 RX and had the same problem, simply because I didn't follow the instructions precisely..

Good luck...Oz

Mar 22, 2009 | 2004 Lexus RX 330

1 Answer

Home link system will not accept garage door code.


I purchased a Chamberlain belt garage door opener. It was great! The lease on my duplex ended and the landlord bought it from me.

I found that the best way to program my vehicle's HomeLink buttons (to read the remote) was to do the learning procedure in a parking garage. This way the signal is not interrupted by all the waves around us.

Jan 02, 2009 | 2001 Lexus ES 300

1 Answer

Garage door opener on 2000 Lexus RX300


Check out the Homelink Website. I found instructions for my wife's GS300 there. I haven't tried it yet, so I'm not 100% sure this will work.

May 22, 2008 | 2000 Lexus RX 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

907 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...