Question about 2002 Buick Rendezvous

Open Question

Torque spec. for a ford ranger 98 3.0 head bolts

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnjnail
  • 1702 Answers

SOURCE: looking for cylinder head torque specs and intake

on the 2.5 4 cylinder

step 1 18 ft lbs.

step 2 26 ft lbs. except bolt #9 re tighten it to 18 ft. lbs.

step 3 all bolts an additional 90 degrees.

intake manifold bolts 65 ft lbs.

on the 3.3L V6

step 1 35 ft lbs.

step 2 tighten all bolts an additional 130 degrees

step 3 tighten center 4 bolts an additional 30 degrees

intake manifold bolts 88 in. lbs.


Posted on May 19, 2011

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

johnjnail
  • 1702 Answers

SOURCE: head bolt torques spec

3.8L V6

cylinder head bolt torque

step 1 37 ft lbs.

step 2 an additional 130 degrees

step 3 4 center bolts an additional 30 degrees

Posted on May 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Torque specs for 2008 ford ranger 4x2 front axle


Torque Specifications

Description Nm lb-ft Axle-to-frame bolt 66 49 Axle damper-to-frame bolt 34 25 Brake caliper guide pin bolt 33 24 Differential bearing cap bolt 61 45 Differential housing cover bolt 29 21 Ring gear bolt 122 90 Tie-rod nut 91 67 U-joint spider retainer bolt 19 14 Upper ball joint pinch bolt 48 35

Sep 18, 2014 | 2008 Ford Ranger 2WD

1 Answer

Ford torque specs


depends on size of engine. what size is your engine?

Jun 24, 2014 | 1992 Ford Ranger

1 Answer

Steps to change a valve cover gaket on a 1992 ford ranger


its not very hard at all. once you get the heads off just make sure you follow the proper sequence to tighten the bolts. always remember to tighten from the center bolts out to the end bolts so the heads seat flat and even. and make sure you have the proper torque specs for those head bolts. 1) hand tighten. 2) torque to half of the OEM spec. 3) full torque spec. all of this takes a while to do so be patient.

Sep 27, 2013 | 1992 Ford Ranger

1 Answer

What do u torque head bolts at for 98 ford ranger 3.0 v6


Its a four step procedure.1. 59ft,lbs. 2.loosen one full turn. 3. 31-41ft lbs. 4. 63-73ft lbs. these are torque to yield bolts and must be new!

Mar 27, 2011 | 1998 Ford Ranger SuperCab

1 Answer

What is the torque pressure on cylinder head bolts for a ford ranger 2.3l engine


The torque specs for the head bolts are 51 ft.lbs.then an additional 90-100 degrees(angle).Hope this helps.Good luck.

Dec 10, 2010 | 1996 Ford Ranger SuperCab

2 Answers

NEED FORD 2.2l head gaskets torque chart


Tighten the head bolts 29 to 32 ft lbs , then tighten again to 59 to 64 ft lbs

Apr 17, 2010 | 1989 Ford Probe

1 Answer

Need torque specs for oil pan bolts


torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

May 17, 2009 | 1997 Ford Ranger SuperCab

3 Answers

Head bolt torque for a 1996 ford ranger 2.3liter


The torque specs and tightening sequence can be found in Haynes repair manual #36071.Ford Ranger 1993-2005

Jun 26, 2008 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
2002 Buick Rendezvous Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...