Question about 1996 BMW 318

Open Question

1984 BMW 318I HEAD TORQUE SPEC - 1996 BMW 318

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

LT1Rob
  • 55 Answers

SOURCE: Torque Settings on a 1994 BMW 318i?

The torque settings is more know as torque spec's, and it just means an exact measurement of how tight a paticular part is tightend. With a new engine, many differnt parts have differnt specs, but hands down the single most important thing would be the cylinder head to engine block torque. This is often done in a 3 step process, using a torque wrench, and a torque angle gauge. Are you planing on installing an engine yourself? I can get specs for you.

Posted on Mar 10, 2009

  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

  • 6 Answers

SOURCE: battery drains in my 1984 BMW 318i

I have the same car I had the same problem.If you have the correct battery for your car with the same problem you have a short or positive ground in your dash/electric fuel pump/fuse box also be carefull of how you take the key from the ignition and if they're old replace them.

Posted on Apr 17, 2009

  • 40 Answers

SOURCE: how do i change the torque settings on my bmw e36

Hi unsure what you mean by change the torque settings, if you mean on the head question is why? If yes for head, there is a tool for that & go to Download PDF search | PDFTown.com
for more info

Posted on Jul 09, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head torque settings bmw 318i m43


Hi dear40,

The m43 engine should be similar to both the m42 and m44. The cylinder head torque settings are 22ft/lb and 90degree torque angle, and another 90 degree torque angle. Make sure to wait approximately 10minutes before performing the 2nd torque angle.

Jun 11, 2011 | 1997 BMW 318

1 Answer

I need to know the timing spec for a 1984 bmw 318i


6? btdc is the static timing firing order 1342 ,hope this is sufficient

Feb 10, 2011 | 1984 BMW 3 Series

1 Answer

I need to know he torque spects for the oil filter container the bolts on to the moter on a 94 BMW 318i...there are 6 bolts...I also need to know the torque spects on the alternator mounting bracket...


OIL PAN OR TRANSMISSION PAN BOLTS TORQUE ABOUT 7 FT LBS. CAN GET SPECS ON BOLTS SIZES. IF BOLTS SIZES IS 13M I4M 15 M TORQUE BOLTS ABOUT 55 TO 80 FT LBS

Nov 11, 2010 | 1994 BMW 3 Series

1 Answer

How do i change the torque settings on my bmw e36 316i 1991 j reg its not a 318i but parts of a 318i would thay fit a 316i and work fine


Hi unsure what you mean by change the torque settings, if you mean on the head question is why? If yes for head, there is a tool for that & go to Download PDF search | PDFTown.com
for more info

Jul 08, 2009 | 1996 BMW 318

1 Answer

To replace rockerarm,do i need to remove the head?first 1 left side facing the car.


You should only have to remove the rocker assembly,the head bolts ussually hold the assembly on,but even if you remove them the head gasket will stay sealed.You'll have to get the torque specs and bolt down sequence,and check to see if its recomended to replace the head bolts.When you dissassemble the rocker assembly lay the parts out in sequece and reassemble in the correct order.Hope this helps.

Apr 23, 2009 | 1984 BMW 7 Series

2 Answers

Torque for head bolts for 1984 Toyota Corolla


head bolt toque specs are 40-47 ft-lbs

Mar 22, 2009 | 1984 Toyota Corolla

1 Answer

Battery drains in my 1984 BMW 318i


I have the same car I had the same problem.If you have the correct battery for your car with the same problem you have a short or positive ground in your dash/electric fuel pump/fuse box also be carefull of how you take the key from the ignition and if they're old replace them.

Mar 19, 2009 | 1984 BMW 3 Series

1 Answer

Torque Settings on a 1994 BMW 318i?


The torque settings is more know as torque spec's, and it just means an exact measurement of how tight a paticular part is tightend. With a new engine, many differnt parts have differnt specs, but hands down the single most important thing would be the cylinder head to engine block torque. This is often done in a 3 step process, using a torque wrench, and a torque angle gauge. Are you planing on installing an engine yourself? I can get specs for you.

Mar 08, 2009 | 1996 BMW 318

Not finding what you are looking for?
1996 BMW 318 Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...