Question about Opel Corsa

1 Answer

Cylinder head torque specs for opel corsa 8valve 1.4l 2005 model

Removed cylinder head and want to reinstall

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Opel Master
  • 14,804 Answers

Corsa 1.4I Engine code Z14XE 2000-2004
Bolts must be renewed
stage 1. 25Nm
stage 2, + 90 degrees
stage 3. + 90 degrees
stage 4. +90 degrees
stage 5. + 45 degrees
Sequence
10 6 2 3 7
9 5 1 4 8
bolts 7 & 8 are nearest to the flywheel side of the engine
Engine code C14NZ 1993-1998
Stage 1. 25Nm
stage 2. + 60 degrees
stage 3. +60 degrees
stage 4. + 60 degrees
Sequence as above.
Corsa 1.4I Engine code Z14XE 2000-2004
Bolts must be renewed
stage 1. 25Nm
stage 2, + 90 degrees
stage 3. + 90 degrees
stage 4. +90 degrees
stage 5. + 45 degrees
Sequence
10 6 2 3 7
9 5 1 4 8
bolts 7 & 8 are nearest to the flywheel side of the engine
Engine code C14NZ 1993-1998
Stage 1. 25Nm
stage 2. + 60 degrees
stage 3. +60 degrees
stage 4. + 60 degrees
Sequence as above. <br />Corsa 1.4I Engine code Z14XE <b>2000-2004</b><br />Bolts must be renewed<br />stage 1. 25Nm<br />stage 2, + 90 degrees<br />stage 3. + 90 degrees<br />stage 4. +90 degrees<br />stage 5. + 45 degrees<br />Sequence<br />10 6 2 3 7<br />9 5 1 4 8<br />bolts 7 & 8 are nearest to the flywheel side of the engine<br />Engine code C14NZ <b>1993-1998</b><br />Stage 1. 25Nm<br />stage 2. + 60 degrees<br />stage 3. +60 degrees<br />stage 4. + 60 degrees<br />Sequence as above.

Posted on Aug 24, 2015

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75797 Answers

SOURCE: 2005 Tucson

camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Posted on Sep 08, 2008

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does it mean when your heads are in need of an overhaul?


What that means are new valve seats and valve guide, with new valve stem,with new or refurbished valves,This is a common need after so many years in service

Mar 15, 2012 | 1991 Lincoln Town Car

1 Answer

How to change head gasket


Unplug all wires and hoses connected to the cylinder head and remove the head cover. You may need to remove the A/C fan to be able to clear it of the studs on the engine block.2 Set the motor to "top dead center," or TDC. Remove the #1 cylinder's spark plug as well as the valve cover so you can observe the springs. Insert a screwdriver into the open spark plug hole, and rotate the motor by hand, counter-clockwise. When the #1 cylinder is on its intake stroke, watch the screwdriver. Turn the motor very slowly until the screwdriver reaches its highest point. Remove the screwdriver. Slide off the timing belt, and be sure you do not rotate the motor any further.3 Remove the head bolts in order, and double check that no coolant lines are still connected. Lift the cylinder head out. It will be very heavy--this is where you'll likely need the help of another person. Remove the old head gasket. 4 Drain the oil from the cylinder head. Clean the pistons, valves, headbolt holes and all other parts with degreaser and a toothbrush. Wipe down with a paper towel when finished.5 Set the new head gasket into the engine block, lining it up correctly. Carefully place the cylinder head back in, on top of the head gasket. Soak the headbolts in oil to lubricate them, then replace them. Tighten each bolt until it is snug--no further.6 Start the torquing sequence, following the directions in your Honda's manual. In most D-series cars, you need to torque each bolt to 22 foot-pounds, then all to 53 foot-pounds. Be certain to follow the correct torquing sequence as indicated in the manual, or you could warp the head.7 Reinstall the timing belt and reconnect all wires and coolant lines.
  • Oct 10, 2011 | 2003 Honda Civic

    1 Answer

    One cylinder is low in my 1998 Volvo s90 and the repair shops says the engine needs to be replaced. Is this true>


    Not necessarily. I assume you mean that the compression on one cylinder is low? This is generally either the rings/cylinder, or valves. Sometimes a blown headgasket can drop compression, but will generally have other symptoms, ie., blown between one cylinder and another, blown between the cylinder and a cooling or oil passage, etc.

    A GOOD shop will check more than compression, to determine where the exact problem is.

    *A head gasket blown between 2 cylinders will have low compression on bothe affected cylinders.
    *A head gasket blown into an oil or cooling passage will blow bubbles (gasses) into the affected area.
    *To check the rings/cylinder, after running the first compression check, put a few ounces of oil into the cylinder through the spark plug hole. Re-run the compression check on that cylinder, and if the compression improves dramatically, you have bad rings on that cylinder.
    *To check the valves, you need what is called a pressure differential guage. You place the affected cylinder at TDC (Top Dead Center) on the compression stroke. You then attach the guage, and apply a set amount of air pressure to the cylinder, usually about 100psi. One dial on the gauge reads input pressure (100psi), and the other reads how much the cylinder is actually holding. A drop of more than 10-15% generally indicates a bad valve in the head (as long as the prevoius checks came out OK). To determine which valve is bad, remove the intake ducting and listen for escaping air (Intake Valve) and listen at the tailpipe for the same (exhaust valve).

    These are general procedures for tests so that you can see if your mechanic has actually performed them or not. If you want to run the tests yourself, I can give you more specific instructions.

    Repairs:
    Head Gasket - need to remove the head and check the head and block for cracks. Then replace the gasket and reinstall the head.
    Bad Valve(s) - need to remove the head and have the bad valves reground or replaced by a machine shop and then reinstall the head.
    Bad Rings/Cylinder - the engine will need to be removed and either machined and rebuilt or replaced.

    Again, if you want any more specifics, please ask.

    Hope this was helpful!

    Sep 17, 2011 | 1998 Volvo S90

    1 Answer

    I am trying to remove and reinstall the cylinder head of my 1994 S 10 pickup truck. I have removed the nuts and bolts holding the intake and exhaust manifolds to the head but I am having some dificulty in...


    Leave the exhaust manifold attached and just push it away. Remove the head bolts and make sure all vacuum lines and fuel lines and water lines are disconnected. Make sure you have the head resurfaced before reinstalling and buy new head bolts. Remember to torque the head bolts to spec. But it seems to me like you pretty much got the hang of it.

    Jan 30, 2011 | 1994 Chevrolet S-10

    1 Answer

    I have oil in my anitfreeze what does that mean? how much does it cost to fix it? Is it worth fixing?


    It means you have a blown head gasket or a cracked cylinder head. Its allowing the oil to mix with the water in the cooling system. You will have to remove the belts and accessory's in front of the timing cover, remove crank pulley, remove the timing cover and then timing belt. Remove all connectors, hoses and lines to the intake and cylinder head (Make sure to mark the hoses and connectors to there location for reinstall), remove the intake manifold if it makes it easier to remove cylinder head, if not leave it on and remove the valve cover, Remove the bolts to the cylinder head and pull it off with the intake manifold attached. You should see the gasket if it is not stuck to the bottom of the head. Installation is reverse. Have a Haynes Manual so you can have your torques and timing routing. Is it worth it, cost to replace head gasket verses another car, you have to make the call. I think so because I like no car payment and I know whats in my car. Get a salvaged cylinder head and new head gasket set, Total cost if you do the work yourself and get a good deal on cylinder head, 300 to 400 dollars. Shop cost 700 to 1500 dollars. Just a Ball Park

    Jan 18, 2011 | 1998 Chevrolet Cavalier

    1 Answer

    Do you have to remove the rocker arms to get to the blown head gasket?


    No sir you do not have to remove the rockers. After removing the headcover you will see the head bolts. Break them loose with a 1/2" breaker bar and remove them starting form the outside and working in a circle towards the center bolts. Be careful when you raise the head form the cylinder block so you do not drop any push rods in the oil pan. You will haver to loosen the rockers and retorque them after you reinstall and retorque the head bolts. You should have the head checked at the automotive machine shop for cracks and warpage before reinstalling it. Thanks for visiting Fixya.com, Rich Any problems just ask .

    Nov 21, 2010 | 1998 Dodge Ram 1500 4WD

    2 Answers

    Torque specification on a 2003 alero cylinder heads 3.4 liter


    3.4L Engine To Remove:
    1. Remove the lower intake manifold.
    2. Remove the exhaust crossover pipe.
    3. If removing the right cylinder head, remove the catalytic converter from exhaust manifold.
    4. If removing the left cylinder head, remove the engine oil dipstick and tube.
    5. Remove the rocker arms and pushrods.
    6. Remove and discard the cylinder head bolts.
    7. Remove the cylinder head.
    8. Clean the mating surfaces on the following items:
      • Cylinder head
      • Cylinder block
      • Intake manifold
    9. Clean the cylinder block bolt threads.
    NOTE: During disassembly, keep the valve train components together for proper location during assembly.
    To Install:
    NOTE: Coat the cylinder head bolt threads using thread sealer.
    1. If removed, install the following components:
      • Exhaust manifold
      • Accessory studs
      • Spark plugs
    2. Place the cylinder head gasket in position over the dowel pins. Ensure that the THIS SIDE UP note is showing.
    3. Install the cylinder head. Cylinder head torque sequence ’99-‘00 gmpc_v6_14.gif

      Cylinder head torque sequence ’01-05 gm-03-34-682.gif

    4. Install the new cylinder head bolts.
      • Tighten the cylinder head bolts a first pass to 44 ft lb (60 Nm).
    5. Tighten the cylinder head bolts in sequence an additional 95 degrees.
    6. Install the intake gasket.
    7. Install the pushrods and rocker arms.
    8. Raise and support the vehicle.
    9. Install the catalytic converter and dipstick tube and indicator if removed.
    10. Lower the vehicle.
    11. Install the exhaust crossover pipe.
    12. Install the intake manifolds.
    13. Connect negative battery cable.
    14. Fill the cooling system.

    Jul 03, 2010 | 2003 Oldsmobile Alero

    1 Answer

    87 toyota...engine dies after 1 minute. very hard to start . runs for a short while at high rpm's, then dies


    you need to remove the cylinder head youe cylinder head seal is gonne and you do not have enough copression in the cylinders take the cylinder head to a machine shop have it rectified and then reinstall with new seals

    Apr 01, 2010 | 1987 Toyota Corolla 2 Door

    3 Answers

    WHAT IS THE COST OF REPAIR ON A HEAD GASKET FOR A 1997 SATURN SC? THANKS, JOE


    1.9L SOHC - head gasket set which includes all gaskets needed to remove cylinder head with thermostat runs about $150.00. Head mechine ( check for cracks and milled ) $145.00. Labor time to remove and reinstall cylinder head 8.5 hrs X shops labor rate.

    1.9L DOHC - head gasket set and thermostat runs about $210.00. Head mechine $175.00. Labor to remove and reinstall cylinder head 10.7 hrs X shop labor rate.

    Labor times per Mitchell labor book, this is a guide all repair shops used.

    Jan 12, 2010 | 1997 Saturn SC

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    6,575 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Opel Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Brad Brown

    Level 3 Expert

    15557 Answers

    george parkes

    Level 3 Expert

    975 Answers

    Are you an Opel Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...