Question about Mazda B2200

Open Question

What are the standard fuel jet sizes on a hitachi carburetor fitted on nissan 1400 bakkies

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 514 Answers

SOURCE: PLEASE COULD YOU SEND ME

first you need to know what year is it and engine size in liters 2.0, 3.0,2.2 etc.and then you can get what you look for,

Posted on Sep 10, 2010

Ad
  • 2002 Answers

SOURCE: holley carburetor 750 free tune ,rebuild and

What you need can't be described here.It would take hours to type. You need a manual. Your best bet would be to check with Haynes. Chilton or Motor have a good rebuild section in their yearly manuals and it covers Holleys with the specs for your vehicle. You should be able to find one relatively cheap on e-bay or kijiji. There was a company called Pederson Publishing that put out a book on Holley's a few years ago but I don't know if they are still around. I suspect you could get good info from Holley too but none of it will be free. Hope this helps.

Posted on Nov 01, 2010

Goofguyster
  • 379 Answers

SOURCE: Nissan NP200 bakkie is cranking

spark plugs spark plug wires

Posted on Aug 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I drive a Nissan 1400 Bakkie its doesn't want to hold idling what czs that


that could be the needle and seat in the carburetor is worn and needs to be replaced. The needle and seat is there to set float level and regulate fuel supply

Aug 12, 2016 | Nissan Cars & Trucks

1 Answer

I drive a Nissan 1400 bakkie (not a champ) i drives good and then starts jerking and wants to die as soon i i give petrol it sounds like its smothering


hi, personally ..i love that bakkie. Ok you changed points condensor, petrol filter! please check.. When it cuts out 1. if the ignition coil is not hot, if so thats your problem.2. also on the carb... over the needle and seat there is a tiny filter... somtimes gets blocked. 3. also check when it stolls if the fuel pump is not hot or pull the outlet fuel from the pump
and crank the engine... note if fuel comes out sufficiently.

May 21, 2014 | 2006 Nissan 1400 Bakkie

1 Answer

HOW TO ASSEMBLE A LDH202A CARBURETOR


Probably the needle valve. You need to put this back in.
Or it could be the float hinge pin. Its a simple carby.

May 06, 2014 | 2006 Nissan 1400 Bakkie

1 Answer

I opened up my 1400 nissan bakkies carburetor to service it and i am not sure where all the differentjets must go


In general there are fewer ways to adjust the newer carbs than the vintage carbs of the past. Often the vacuum at low idle is the problem and you should check a vacuum port on the intake with a Vacuum gauge. Sometimes an EGR valve does not shut completely and the engine struggles at idle. If you find that vacuum is adequate, you can adjust the air mixture screws to provide the highest vacuum reading and then crank them in until the vacuum falls less than 1 inch. It might be beneficial to run the engine and spray a water mist from a hand powered spray bottle around the seams of the intake and carburetor. Also spray any vacuum solenoids or lines. You will notice a change in RPM if there is a leak. You may have a fuelpump problem A clogged fuel filter or low pressure can affect how the caricon1.png idles. Please rate my info.

Jan 21, 2014 | 2007 Nissan 1400 Bakkie

1 Answer

CARBURATOR OF NISSAN 1400 BAKKIE


the ball bearing will be a non return valve for the accelerator pump. When the pump is moved to suck in fuel from the bowl it lifts of the seat and when the pump is pressed down the force of the fuel closes it off and the fuel is squirted in to the manifold.

Jan 19, 2014 | Nissan Cars & Trucks

1 Answer

Where is the flasher relay on a nissan 1400 bakkie


this is a super old question, 3 years old, is it worth answering?

Feb 10, 2012 | Nissan 1400 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...