Question about 2007 GMC Yukon Denali

Open Question

Is there a fuse for the oil pressure gauge on 2007 gmc yukon

The gauge wont work

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000

No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 27, 2009

Ad
  • 5 Answers

SOURCE: oil pressure gauge reads 80 while running

could be one of two things, oil pressure switch (located on top of engine behind intake) or instrument panel cluster, if your vehicle has under 70,000 miles, it's covered under warrenty

Posted on Jun 19, 2009

  • 7353 Answers

SOURCE: 2006 Yukon Denali, oil pressure gauge malfunction

Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Posted on Oct 30, 2009

  • 7353 Answers

SOURCE: Replace headlamps 2007 GMC Yukon

It should be pretty easy, thats why there no "directions" Lift up the hood, now at the headlights there should be 2 rods, lift these rods and the lights should lift out, to access the bulbs.

Posted on Nov 06, 2009

fixitriteman
  • 431 Answers

SOURCE: LOW OIL PRESSURE ON 2007 GMC SIERRA 1500. CHANGED

have it tested using a manual gage if still low then main baring ore most likely bad that would mean a over hall if is really low and bearings bad should be making rattle noise when started up first few seconds

Posted on Mar 11, 2010

Testimonial: "thanks alot.truck is not making a rattling noise.we did check it with a manual gauge.it read about 10 at idol. press. gets better as you incr speed"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil Pressure Gauge not working on my 2005 Yukon XL


Those gauges are electric now, check to see if the wire is on good. The sending unit can fail, cheap and easy once you find it, but requires a special socket, get that at the same time.

Nov 30, 2013 | GMC Cars & Trucks

2 Answers

While drivingoil pressure is at 40. after half hour of highway driving oil pressure drops to 0 or below. i stop and restart oil pressure comes back. ideas?


Could be the Oil Pressure Sending Unit. I do recall GMC having issues with the instrument cluster on 2003's. Try slapping the dash when the gage reads zero.

Mar 17, 2013 | 2003 GMC Yukon XL

1 Answer

2002 4.8l gmc yukon oil pressure problem


My suggestion would be to check it with a mechanical gauge.
You would need to use a Tee fitting to use the sensor to have fuel pressure.
If the mechanical gauge shows steady pressure at idle, it could be a problem in the wiring or the instrument cluster.

Jan 27, 2013 | 2002 GMC Yukon

1 Answer

When I first start my yukon it has 45 pounds of pressure but when I drive it the oil pressure goes to 10


I would suggest taking the oil pressure sender out and temporarily connecting a manual gauge to the engine. Run the engine until it's warm. If the manual gauge reads the same pressure as the electric one you may have a serious engine problem. If the manual gauge reads normal when the engine is warm the problem is probably with the gauge, most likely the sender.

Apr 10, 2011 | 1994 GMC Yukon

1 Answer

I have a 2003 yukon denali and my oil pressure gauge went to Zero. Does tis mean I have to replace the oil pump? the car does turn on.


You might want to use a oil pressure test gauge and verify the actual oil pressure. You would connect it to where the sending unit screws into the engine. It's on the driver side back of the motor, under the distributor area. by the fuel lines.

Apr 30, 2010 | 2003 GMC Yukon Denali

1 Answer

2007 GMC Yukon gauge cluster not working, doors lock continuously going down the road, but it still runs


I have a 2007 GMC Yukon and all of the guages (speed, oil, battery, etc.) recently stopped working for no apparent reason. The backlight still works but the guages do not. Could this be something as simple as a fuse? What should I do?

Jan 04, 2010 | 2007 GMC Yukon

2 Answers

2006 Yukon Denali, oil pressure gauge malfunction


Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Oct 30, 2009 | 2006 GMC Yukon Denali

1 Answer

2004 yukon xl oil and fuel gauges do not work.


2 things come to mide off the bat loose or corroded ground or cluster going bad

Jan 17, 2009 | 2002 GMC Yukon XL

Not finding what you are looking for?
2007 GMC Yukon Denali Logo

Related Topics:

493 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...