Question about 2004 Honda Accord

Open Question

Removing windshield wiper cowling on Honda 2006

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 566 Answers

SOURCE: windshield wipers on 1991 Honda Accord

hi from the uk to adjust n/side wiper arm ? if you look at where the wiper arm is fitted below screen you may have a cap/covering that conseals the nut that fastens the arm to the motor wiper spindle which has a milti spline for adjusting? remove nut and pull up the arm and reposition as to prevent hitting bottom of screen ?? however if your wiper arms are the type without this nut fastening ? then same principle as above for readjusting but you will have to raise the arm verticle and carefully prise the arm off spindle there is a tool for this job and makes it easier it is a wiper arm puller you may be able to borrow or purchase? they cost approx £11 in uk but can be used for multiple other jobs ? so try 1st method you may be lucky ? when you reposition arm tap it on firmly!when you are happy with position ? good luck !

Posted on Nov 12, 2008

emissionwiz
  • 75822 Answers

SOURCE: wipers stop in the midle

TSB (Technical Service Bulletin) #07071 -- WINDSHIELD WIPERS INTERMITTENTLY DO NOT PARK OR TURN OFF. Contact your dealer about this problem, it only affects 2006 models of your car. The fix is a new wiper motor I believe.

Posted on Dec 08, 2008

  • 2 Answers

SOURCE: problem removing rear wiper on 2006 honda pilot

You can't replace the wiper. But Parts department at any Honda dealer should sell the replacement blade (just the rubber part). I believe it was under $10. Good luck!

Posted on Aug 10, 2009

  • 318 Answers

SOURCE: Windshield wiper fluid reservoir goes dry

After you pour the stuff in watch where it comes out. It is buried in the fender ...drivers side. Wheel well shield is removeable.

Posted on Oct 27, 2009

Wipers123
  • 15 Answers

SOURCE: how do you remove and replace windshield wiper

If your arm looks like a hook (which it should), once you find and press the little tab and then jiggle the wiper and firmly pull towards the open side of the arm hook, it should come loose. You will probably have to rotate the blade to the side to make space to clear the hook (sometimes the hook flexes the blade a bit which is ok). Be careful not to bend the arm but be firm.

FYI, All new replacement windshield wiper blades come with step-by-step, illustrated instructions. Fon't have anxiety about it - I highly recommend getting the wipers in your hands and physically take a look.

Lastly, make sure you get not only the right length of replacement wiper, get the correct attachement. If you always use the application guide, you will get both: attachement and length. The application guides are at the store or you can go online to look them up (google something like lookup wiper size).

Hope this helps,
Jeff

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the windshield cowl on a 2002 tyota yaris


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------


Complete wiper components replacing details ?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------



1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------


These details will help.

Thanks.

Nov 28, 2012 | Toyota Yaris Cars & Trucks

1 Answer

How to replace the wiper motor on a 1994 volkswagon golf


The wiper motor on a Volkswagen is an electric motor connected through a drive linkage to the wiper arms. Windshield wipers are an integral feature for operating a motor vehicle safely. If your wipers are not functioning, or seem to lack the speed or power they used to have, the wiper motor should be removed and replaced immediately
.


Location
  • The wiper motor on a Volkswagen is located directly underneath the plastic cowl cover. The cowl cover is located directly below the windshield.

Removal
  • Begin by removing the wiper arms by prying off the covers at the base of the arms and removing the nuts that secure the arms to the drive shafts. Label the passenger and driver arms so they can be installed in the same positions. They are not interchangeable. Remove the rubber hood to cowl weather seal. Unscrew the plastic fasteners from the driver's side of the cowl cover, then remove this half of the cover. Remove the fasteners from the passenger's side cowl cover and remove this half of the cover. Disconnect the windshield wiper motor wiring harness by separating the plastic wiring connector. Remove the three bolts that secure the wiper motor to the vehicle's body. Pull the motor slightly away from the body, then remove the nut that connects the motor shaft to wiper linkage. Remove the motor.

Installation
  • Place the new wiper motor into position in the cowl and reconnect it to the wiper arm linkage. Then reinstall the three retaining bolts. Reconnect the plastic wiring connector to the wiper motor wiring harness. Place the cowl covers into position below the windshield and reinstall the plastic fasteners that retain them. Reinstall the rubber hood to the cowl weather seal. Reinstall the wiper arms in the same position you removed them from, along with the wiper arm retaining nuts and lower wiper arm covers. Turn the windshield wipers on and test for proper operation. If the wiper blades slap against the bodywork surrounding the windshield, loosen the nuts that connect the wiper arms to the shafts and adjust.

More Read: OBD2 car diagnostic tool

Aug 06, 2012 | 1994 Volkswagen Golf

1 Answer

The windshield wipers to my Ford focus stopped working today. They worked for a little while & then stopped in the up position. You can hear the motor working but they don't move. You can move them...


Your wiper linkage has come off the wiper motor. To reconnect the linkage, first remove the wiped arms, the remove the wiped cowl. The wiper cowl bolts are located under the hood and screws through the spaces in the cowl. Reconnect linkage, reinstall cowl, reinstall wiped arms.

Jul 05, 2011 | 2006 Ford Focus

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

When I turn on the windshield wipers they travel too far hitting the windshild pillar(top) and the the cowl(bottom).


The wipers are not installed correctly. Remove and reposition the wiper arms ,so they do not hit the side of the outside window pillar,when set to high speed.

Apr 28, 2010 | 2003 Honda CR-V

1 Answer

Ford Taurus 1999SE-Windshield wiper motor just hums.How to fix ?


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the wiper arms.
  4. Remove the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to remove.
  5. Remove the cowl vent screens.
  6. Disconnect the electrical connector from the wiper motor and remove the 4 bolts that mount the module assembly to the cowl.
  7. Remove the windshield wiper module from the vehicle.
  8. Rotate the wiper operating arm in a clockwise direction to gain access to the bolt retaining the arm to the motor. WARNING
    Always rotate the wiper operating arm in a clockwise motion or damage to the motor could occur.
  9. Remove the nut retaining the wiper operating arm to the wiper motor.
  10. Remove the three wiper motor-to-wiper module assembly retaining bolts and remove the motor from the vehicle.
To Install:
  1. Position the wiper motor on to the module assembly. Install the three wiper motor-to-wiper module assembly retaining bolts. Tighten the bolts to 115-151 in lbs (13-17 Nm).
  2. Position the wiper operating arm on the wiper motor output shaft. Install the mounting nut and tighten to 22-29 ft-lbs (30-40 Nm).
  3. Position the windshield wiper module onto the cowl. Install the mounting bolts and tighten to 106 in-lbs (12 Nm).
  4. Connect the wiper motor electrical connector.
  5. Position the cowl vent screens onto the inner panels. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to install.
  6. Install the wiper arms.
  7. Connect the battery ground cable.
  8. Adjust wiper arms if necessary.

Here is the picture of the motor....it is the round object in the middle of the picture that looks like a can and has a square block on the end of it.

You have to remove the cowl vent panel....just under the windshield. $64.00 for a new motor.

Oct 01, 2009 | Ford Taurus Cars & Trucks

2 Answers

Front Windsheild Wipers


I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield s7w~us~en~file=adobe.gif~gen~ref.gif Printable View (104 KB) Removal
  1. Remove the windshield wiper arms.
  1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
    Remove the pushpin-type retainers and the cowl panel grille.
  1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.
  1. If equipped, remove the A/C air inlet filter.
  1. Remove the 9 cowl panel bolts and position aside the cowl panel.
  1. Disconnect the windshield wiper motor electrical connector.
  1. Remove the cowl panel from the vehicle.
  1. Remove the 4 bolts and the windshield wiper motor.
    s7w~us~en~file=n0001518.gif~gen~ref.gif
Installation
  1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
    • Tighten to 15 Nm (11 lb-ft).
  1. Install the 3 windshield wiper-to-cowl panel bolts.
    • Tighten to 15 Nm (11 lb-ft).
  1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.
  1. Install the washer hose and grommet in the cowl panel.
  1. Install the 9 cowl panel bolts.
    • Tighten to 6 Nm (53 lb-in).
  1. If equipped, install the A/C air inlet filter.
  1. Position the cowl panel grille in the vehicle and connect the washer hose.
  1. Install the pushpins.
  1. Install the windshield arms and nuts.
    • Tighten to 27 Nm (20 lb-ft).
  1. Cycle and park the windshield wipers to check for correct alignment.
3c6f4d5.gif
b8a2ebf.gif

Apr 09, 2009 | 2006 Ford Freestar

1 Answer

The wiper blade connection has released from the wiper blade motor bar that controls the wipers movement. You can hear the motor working but the arms have been disengaged.


please rate as fixya if this is what you need. Mounting Arm and Pivot Shaft —Windshield Wiper Removal
NOTE: The windshield wiper pivot arms (17526) must be in the highest position to remove them.
  1. Turn the ignition switch (11572) to the on position.
  1. Turn the windshield wiper (17500) on.
  1. Stop the windshield wiper pivot arms at the highest position by turning the ignition switch off.
  1. Remove the windshield wiper pivot arm.
    1. Remove the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the windshield wiper pivot arm.

  1. Raise and support the hood (16612).
  1. Remove the cowl grille seal.
NOTE: The two cowl grilles overlap at the center. The LH cowl grille must be removed first.
  1. Remove the LH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the LH cowl grille.
6a042b2.gif
  1. Remove the RH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the RH cowl grille.
bfba69b.gif
  1. Remove the mounting arm and pivot shaft.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the mounting arm and pivot shaft.
8169c1e.gif

Mar 14, 2009 | 2000 Ford Expedition

1 Answer

ROVER MGF.REMOVING WIPER MECHANISM.


Pivot Shafts and Linkage
The windshield wiper assembly is mounted below cowl top extension (021A36) . Linkages are connected with non-removable plastic ball joints. Windshield wiper mounting arm and pivot shafts are an integral part of the windshield wiper and are serviced as one unit. Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove antenna mast from the antenna base.
  1. Remove cap on LH and RH windshield wiper pivot arms to expose nuts retaining the arms to pivot shafts.
  1. Remove two nuts, one from each of windshield wiper pivot arms . Lift wiper arms to service position, carefully rocking them back and forth to loosen them from the pivot shaft. Lift off windshield wiper pivot arms .
  1. Remove seven screws retaining the cowl top vent panel.
  1. Disconnect windshield washer hose (17A605) at LH side of vehicle just ahead of where it enters cowl top.
  1. Remove hood cowl seal.
  1. Carefully remove cowl top vent panel from vehicle.
  1. Remove three retaining screws to cowl drain tube that is connected to top cowl.
  1. Disconnect wiring harness leading to windshield wiper motor.
  1. Remove five screws retaining cowl top to vehicle and remove cowl top and windshield wiper from vehicle.
  1. Remove two screws and two nuts retaining windshield wiper to cowl top and separate the two parts.
  1. Remove drive linkage from motor shaft linkage.
  1. Remove remaining screws attaching windshield wiper and separate the two parts.
1086bde.gif

Item Part Number Description 1 02010 Cowl Top Panel 2 N621906-S2 Nut (2 Req'd) 3 17508 Windshield Wiper Motor 4 N805605-S36 Screw (2 Req'd) 5 17500 Windshield Wiper Assembly A — Tighten to 9-12 Nm (80-106 Lb-In)

Feb 23, 2009 | 1998 Ford Windstar

2 Answers

How to Fit a Cabin Filter


Hiya...the cabin air filter is located below the front passenger/windshield area.
It's only accessible by standing outside the Equinox with the hood open.
Here's how to do it...(before you pop open the hood)

1) Stand outside at the front-right door area.
2) Just below the front windshield area, pull up a few small black plastic clips that's on the black windshield wiper cowl area- a small flat screwdriver or a special clip-remover tool is handy.
3) Raise the hood up.
4) There may be a triangular-shaped hard foam sound damper at the left side nearby the hood hinge...pull it off if it allow you to work around it with ease.
5) Continue to find a few black plastic clips around the black windshield wiper cowl area.
6) Gently pull up the black windshield wiper cowl cover with care not to bend it too hard during removal.
7) You should see the cabin air filter inside that's held in place by a black rectangular box inside.
8) There's 2 black tabs that holds the cabin air filter in place.
9) Insert your finger or tool to pry the cabin air filter away from the tabs.
10) Remove old cabin air filter.

Remember to reinstall the clip parts back into place when you're finished.

Nov 12, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
2004 Honda Accord Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...