Question about 1994 Ford Explorer Limited

Open Question

Need to know how to install rear main seal on 2005 vw jetta 2.5gasoline

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 92 Answers

SOURCE: how toreplace rear main seal in 92 F150 4.9 inline 6

A- you will have to drop oil pan,then remove rear bearing cap.they market a chinese finger that can install in the upper chanber, seat lower half in cap groove install cap . bolts finger tight, then torque, both bolts evenly as you can until done to manufactures specs.

Posted on Oct 05, 2008

Ad
  • 142 Answers

SOURCE: rear main seal

when i replace rear main seals i use a nylon drift/block and a hammer, and tap them in evenly and carefully,
as long as the tools are not sharp and have curved edges(as not to damage the seal) and you are carefull .... and even, all is good.
i start at 12'o'clock position, then 6,3,9, in small amount, then repeat.

Posted on Jan 28, 2009

emissionwiz
  • 77201 Answers

SOURCE: rear main seal is leaking on a Ford Mustang 2003 V-6

In order to replace the rear main seal u have to pull the transmission out to access it, u will need a special seal installer tool to install the new rear main "full circle seal", it u don't use the special ford tool the seal will leak again, also if there is a groove worn ion the crankshaft the crank must be repaired or replaced or the or the seal will leak again, so this is avery diff job, a 9 on the scale of 1-10 with 10 being the mos difficult.

Posted on May 11, 2009

  • 1403 Answers

SOURCE: i need a diagram on

try webresourful.com for a complete auto manual,

Posted on Aug 15, 2010

emissionwiz
  • 77201 Answers

SOURCE: possible leak from my rear main seal on 87 bronco 2

The valve cover gaskets are prone to leaks and bad ones at that. Cleans the entire engine and rive it to confirm the source of the leaks or leaks.. Remember the oil runs down hill and to the rear of the engine and gets all over from leaking valve cover gaskets.

Posted on Nov 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 vw jetta changing trans oil


Your 2001 VW Jetta is likely equipped with a "sealed" transmission unit. There is no dipstick that you can use to measure the level of transmission fluid in sealed transmissions. Unfortunately, it's a dealer item that needs to be addressed by a qualified mechanic or at a VW dealer.

Jul 01, 2014 | 2000 Volkswagen Jetta TDI

1 Answer

Where is the clutch release bearing on a 1997 vw jetta


It is located on the transmission input shaft collar of the transmission inside the bell housing.

Sep 07, 2012 | Cars & Trucks

1 Answer

I need to know how to replace the rear main seal in a 1993 jetta toinght i all ready have the parts


short answer is the transmission has to come out then its easy after that just pull the old seal out and tap the new one in place

Mar 14, 2010 | 1993 Volkswagen Jetta

2 Answers

How to install a bov on a 2000-2004 vw jetta


It is not wise to install a BOV on a 1.8t since it could cause problems with stalling in between shifts if it is vented to the atmosphere. The most recommended aftermarket solution is a new diverter valve (ex: Baileys, APR etc). If you still want to install the BOV they sell kits for the ssqv that mounts it to the charge pipe and routes the air back to the intake.

Nov 05, 2009 | 2004 Volkswagen Jetta

1 Answer

How do i replace the rear tail light on my 2005 VW Jetta?


Get a set of new bulbs.
Remove lens by disconecting rotary knob retainer from the inside , remove old bulbs,
straighten spring clips in socket and aply di electric grease instal bulbs ,,,test.
Vitally

Sep 09, 2009 | 2005 Volkswagen Jetta

1 Answer

How to replace 2005 VW Jetta brakes. Will be nice to have a picture or video on how to replace front and back breaks on a Jetta 2005


the front and rear pads are very easy to replace although you do need a piston wind back tool to replace the rears,my concern is if you are having to ask this question you probally should not be fitting the pads being a safety related item you cannot take risks.my best and honest advice would be to get a mechanic to replace them for you.Sorry if you dont think i,m being helpfull but you cant take chances with brakes.cheers

Aug 26, 2009 | 2005 Volkswagen Jetta

1 Answer

Need to fix 2005 Jetta Rear brakes


At VW $189 without rotors about $350 with rotors

Dec 26, 2008 | 2005 Volkswagen Jetta

1 Answer

2005 VW Jetta Light on when car starts, goes off when in gear


it is just letting you know that your foot is not on the brake thats it.

Dec 14, 2008 | 2005 Volkswagen Jetta

1 Answer

VW Jetta 2005 engine indentification needed


The dealer gets there build info via computer link to the manufacturer data base for paticular car, you can be 99.99% it is correct.

Oct 17, 2008 | 2005 Volkswagen Jetta

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...