Question about 1995 Jeep Wrangler

Open Question

Socket size for starter mount bolt 1995 jeep wrangler

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2007 jeep wrangler sahara with a mopar remote starter just beeps

That's not a remote starter on your key chain, it's a keyless entry for an alarm system.

Posted on Dec 17, 2008

Ad
  • 5 Answers

SOURCE: 4wd problem jeep wrangler yj 1995

i just bought a used 97 CHEROKEE but i had the same problem, when i got to looking at it i found out the front driveshaft was shot, look at that, if its not it i would say its probably the transfer case especially with an older vehicle like that which is a very expenxive repair

Posted on Dec 21, 2008

  • 124 Answers

SOURCE: how to change starter on 1994 jeep wrangler

is it the straight six? if so first disconnect the battery then there should be 2 bolt 13 or 14 mm. take wires off. then reverse for install.

Posted on Mar 11, 2009

MNfisherman
  • 11896 Answers

SOURCE: how do i remove a starter from a 1995 jeep wrangler

Raise vehicle, disconnect negative battery cable. remove two nuts and wires holding cables with approx 3/8 socket. It will probably be metric.

Then remove two retaining bolts holding starter. remove starter
Reverse procedure to reinstall.

For more information you can view your free online repair manual at;

http://www.autozone.com

http://www.autozone.com/autozone/repairinfo/common/repairInfoMain.jsp?targetPage=productsHowToInspect&leftNavPage=productsHowTo&pageId=%0900045_starterreplace.xml&subtitle=replace

Posted on Apr 01, 2009

  • 6982 Answers

SOURCE: location/testing of crank sensor 1995 jeep wrangler

Should be on the bellhousing on the drivers side just where you need rubber arms to reach it.Should have no continuity between b&c terminals (check with ohmeter) Harness plug is usually on the drivers side between the master cyl and the back of the engine (unless someone moved it)

Posted on Apr 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing starter


yours is out?
all starters are same. on all cars. (gas)
the book is free, posted over 300 times.
click free fsm here
http://jeepdied.com/

or watch 1000s do it on ebay.

1: disconnect battery post NEG lug first. and tie it back (safe)
2: gain access to starter (the only variance on cars)
3: remove the wire cables, there.(on solenoid)
4: remove the mounting bolts. on starter.
5: it falls and hits your head, (duck)
6: reverse from here.

put the lug back last ! no boom;no eat acid.

Apr 19, 2016 | 1995 Jeep Wrangler

1 Answer

How to remove the top bolt on a 2008 jeep wrangler starter


with a socket + universal and an extension?
you dont have full tools set?
which engine,? gas or diesel? 3.8L
my 2008 6speed, is yours 5 m.t or slush pump.>? a/t
on mine, its easy.
but cant answer with no engine stated or trans.
or car bodies are same ,for sure. 2door.? right>?

mine is 3.8L v6
i own a full FSM. too.
7400 pages.
the books shows removing battery neg lug, or boom.acid bath

then shield
then says remove starter. see the bolts there?
then as it drops down take of the solenoid wires.
its you hands.
it assumes you have full set of tools.
extensions, universals., and sockets.

but no engine options stated.or transmission.

Aug 27, 2014 | 2008 Jeep Wrangler Rubicon

1 Answer

Does a 1998 Jeep wrangler starter require a shim? Replacement starter is leaving a 3/8 " gap when mounted.


You likely don't need shims in fact that will make it worse.The replacement starter is likely a starter that will work on your vehicle but is not the same model as the starter that you removed.If this is the case then you will need shorter mounting bolts or a stack of about 4 washer between the bolt heads and the starter.Usually the rebuilt starters are made from cores that are the cheapest to rebuild so it is likely that this is what has happened.

Sep 12, 2010 | 1998 Jeep Wrangler

1 Answer

Cant get starter out in a 2001 jeep wagler 2.5 litter 4


Once you remove the starter mounting bolts and wires from the solenoid, the starter should pull right out and allow you to drop it down.
If you have a 3.7 it will take some more dis-assembly, but you have a 4 cylinder.

Apr 01, 2010 | 2001 Jeep Wrangler

2 Answers

NEED TO TIGHTEN FAN BELT ON 1997 JEEP WRANGLER


If a 6cyl, from the front of engine, loosen the idler pulley with a 15mm wrench. It's on the left side of the engine. Then from the top, use a 15mm socket on a 6 inch extension, and tighten the adjustment bolt that is mounted diagonally just behind the idler pulley. takes alot of turns to tighten the belt. Then retighten the idler pulley bolt with wrench.

Nov 05, 2009 | 1997 Jeep Wrangler

1 Answer

How do you install a factory hardtop on a 1995 jeep wrangler


It's best to have a friend help you through this process. Along the inside perimeter of the base of the top there are about 8 or 10 mounting bolts. Make sure you have all the mounting hardware before starting. The top is not that heavy but it IS awkward, hence the friend helping out. Just align the bolts/nuts and tighten them down. That's it.

Sep 30, 2009 | 1995 Jeep Wrangler

2 Answers

Wont start, new battery, relay good, starter good.


Check the Starter Solenoid mounted near the battery.Check it out in the dark...have someone try to start it and see if it sparks at the solenoid.connections may be loose.Also check/wiggle wiring harness to starter.

Apr 18, 2009 | 1995 Jeep Wrangler

1 Answer

How do i remove a starter from a 1995 jeep wrangler


Raise vehicle, disconnect negative battery cable. remove two nuts and wires holding cables with approx 3/8 socket. It will probably be metric.

Then remove two retaining bolts holding starter. remove starter
Reverse procedure to reinstall.

For more information you can view your free online repair manual at;

http://www.autozone.com

http://www.autozone.com/autozone/repairinfo/common/repairInfoMain.jsp?targetPage=productsHowToInspect&leftNavPage=productsHowTo&pageId=%0900045_starterreplace.xml&subtitle=replace

Apr 01, 2009 | 1995 Jeep Wrangler

1 Answer

1995 jeep wrangler water pump removal


Remove fan belts first, then removed fan pulley bolts these are on the front center of the fan hub,,,remove these bolts.
Then remove the fan, and hub off the front of the water pump,,then remove the coolant hoses,,make sure you use a drain bucket to catch all of the antifreeze.
Then remove the water pump mounting bolts,,and gently pry off the water pump.
Then go get a new one.
Before install,,make sure you take a scraper and clean off any old gasket material first before installing the new gasket.
Then re-install the new pump.

Jan 16, 2009 | 1995 Jeep Wrangler

Not finding what you are looking for?
1995 Jeep Wrangler Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...