Question about 1989 Cadillac Allante

Open Question

1989 Cadillac allante water pump bolt size

Water pump pulley bolt size

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

outdoorsman5
  • 631 Answers

SOURCE: water pump still leaks 92 cadillac deville

I hate to tell you this because I know it isn't an easy task changing the water pump but if it is coming between the block and the water pump housing you need to pull it back off and make real sure it is very clean by scraping the old gasket off and putting sealer on the gasket. Every bit of the old gasket has to be removed before putting the new gasket on. You could try and tighten down your bolts a little but be careful not to break the bolt or you then have another problem.

Posted on Jul 28, 2009

  • 61 Answers

SOURCE: where is the water pump located on a 1989 cadillac

located on front of engine above harmonic balancer sugest you have mechanic replace due to dificulty if bolts are overtightend you could end up replaceing timing cover.

Posted on Apr 21, 2010

ftw1952
  • 10319 Answers

SOURCE: allante

best to purchase a service manaul
most are found at a decent price on ebay

Posted on Jul 30, 2010

duane_wong
  • 6826 Answers

SOURCE: my cadillac eldorado etc 98

The water pump should come with a pulley on it or at least transfer over to the new one if it doesn't come with a pulley. Water Pump Removal and Installation All Engines To Remove:

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section.
  2. Remove or disconnect the following:
    • Coolant into a suitable container
    • Upper filler panel
    • Air cleaner assembly
    • Secondary AIR injection control valve gm_car_cad_sev_wtr_pmp_belt_shld.gif

    • Oil level indicator tube nut
    • Water pump belt shield fasteners
    • Water pump belt shield gm_car_cad_sev_wtr_pmp_drv_belt.gif

    • Water pump drive belt (D) gm_car_cad_sev_rad_outl_hos.gif

    • Radiator outlet hose from the thermostat housing gm_car_cad_sev_wtr_pmp_and_covr.gif

    • Water pump cover bolts
    • Water pump cover
    • Heater return hose
    gm_car_cad_sev_wtr_pmp_pulr.gif

  3. Position suitable water pump puller/installer tool (or special service tool J38816-A) to the water pump locking ears.
  4. Fasten the support plate to the water housing crossover to ensure proper engagement of the tool to the water pump locking ears.
  5. Remove or disconnect the following:
    • Pump from the housing:
      1. Use suitable water pump puller/installer tool (or special service tool J38816-A) to turn the pump clockwise
    • Support plate from the water housing crossover gm_car_cad_sev_wtr_pmp_rem.gif

    • Water pump
    • Seal from the water crossover
  6. Clean the sealing surfaces of the water housing crossover and the pump cover.
  7. Clean and inspect the water pump.
To Install:
  1. Install or connect the following:
    • Seal into the recessed portion of the water crossover
    gm_car_cad_sev_wtr_pmp_crosovr_seal.gif

    NOTE: The notched locking ear must be in the 7 o'clock position.
  2. Index the water pumps locking ears with the tangs in the water crossover.
  3. Position suitable water pump puller/installer tool (or special service tool J38816-A) to the water pump locking ears.
  4. Fasten the support plate to the water housing crossover to ensure proper engagement of the tool to the water pump locking ears.
  5. Turn suitable water pump puller/installer tool (or special service tool J38816-A) counterclockwise.
  6. Torque the water pump
    • Torque to: 74 ft. lbs. (100 Nm)
  7. Remove the support plate from the water housing crossover.
  8. Install or connect the following:
    • Water pump cover to the heater return hose
    • Water pump cover to the water housing crossover
    • Water pump cover bolts
      1. Torque to 89 inch. lbs. (10 Nm)
    • Radiator outlet hose to the thermostat housing
    • Water pump drive belt
  9. Place the water pump belt shield in position.
  10. Install or connect the following:
    • Water pump belt shield fasteners
      1. Torque to 89 inch. lbs. (10 Nm)
    • Oil level indicator tube nut
      1. Torque to 89 inch. lbs. (10 Nm)
    • Secondary AIR injection control valve
    • Air cleaner assembly
    • Upper filler panel
  11. Fill the cooling system.
  12. Start the engine then idle until normal operating temperature is attained.
  13. Recheck coolant level and top off as needed.
  14. Test drive the vehicle.
prev.gif next.gif

Posted on Aug 17, 2010

  • 7353 Answers

SOURCE: how do i remove a water pump pulley for a 2000

you cant take the pulley off , you have to remove the complete water pump. special tools are needed.

Posted on Dec 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water pump


Which engine?

  1. Drain the radiator

91192665


  1. Loosen the water pump pulley bolts.
  2. Remove the serpentine belt.

91192666
  1. Remove the water pump pulley bolts and pulley.
  2. Remove the water pump bolts, pump and gasket.
  3. Clean the water pump mating surfaces.
Installation Procedure
  1. Install the water pump gasket and pump.
91192667


  1. Install the water pump bolts. Tighten the water pump bolts to 89 inch lbs.

91192668
  • Install the water pump pulley and bolt until snug.
  • Install the serpentine belt.
  • Tighten the water pump pulley bolts. Tighten the water pump pulley bolts to 18 ft. lbs.
  • Fill the cooling system and purge of air.
  • Inspect for leaks.
  • Sep 27, 2012 | 2001 Oldsmobile Alero

    1 Answer

    How do you change water pump on a olds 98 regency


    first pop the hood and locate the water pump pulley. drain the coolant into a suitable container. there will be alot of it so get a big container.use the correct size socket and loosen the four small bolts on the pulley.DO NOT TAKE THEM ALL THE WAY OUT YET. find the tensioner pulley and put a socket on the bolt and lift the pulley to release the pressure on the fan belt and slip it off the water pump pulley.now remove the bolts from the water pump pulley. now all you have to do is remove the bolts that attach the pump to the engine block. remove the pump and clean the surface of the the engine block where the pump connects to the block. don't scratch the matting surface of the block.oh disconnect the coolant hoses that attach to the water pump.BE CAREFUL THE COOLANT WILL DRAIN OUT OF THE BLOCK AND HOSES. DOGS AND CATS ARE ATTRACTED TO THE COOLANT, IT WILL KILL THEM IF THEY DRINK IT.have fun

    Jun 11, 2012 | Oldsmobile Regency Cars & Trucks

    1 Answer

    How to change a water pump on a 1995 ford windstar


    7e7c53c.jpg

    Fig. 1: Front cover and water pump bolt size and location-3.0L engine
    1. Disconnect the negative battery cable.
    2. Drain and recycle the engine coolant.
    3. Loosen the four water pump pulley retaining bolts while the accessory drive belts are still tight.
    4. Rotate the automatic tensioner down and to the left.
    5. Remove the accessory drive belt.
    6. Remove the two nuts and bolt retaining the drive belt automatic tensioner to the engine, then remove the tensioner.
    7. Disconnect and remove the lower radiator and heater hose from the water pump.
    8. Remove the eleven water pump-to-engine retaining bolts, then lift the water pump and pulley up and out of the vehicle.
    9. Remove the water pump pulley retaining bolts, then remove the pulley from the water pump.
    To install:
    Be careful not to gouge the aluminum surfaces when scraping the old gasket material from the mating surfaces of the water pump and front cover.
    1. Clean the gasket surfaces on the water pump and front cover. Lightly oil all bolt and stud threads except those requiring special sealant.
    2. Position a new water pump housing gasket on the water pump sealing surface using gasket sealant to hold the gasket in place.
    3. With the water pump pulley and retaining bolts loosely installed on the water pump, align the water pump-to-engine front cover, then install the retaining bolts.
    4. Tighten the bolts to the following specifications:
      1. Bolt numbers 1-10: 15-22 ft. lbs. (20-30 Nm).
      2. Bolt numbers 11-15: 71-106 inch lbs (8-12 Nm).
    5. Hand-tighten the water pump pulley retaining bolts.
    6. Install the automatic belt tensioner assembly. Tighten the two retaining nuts and bolt to 35 ft. lbs. (47 Nm).
    7. Install the alternator and power steering belts. Final tighten the water pump pulley retaining bolts to 15-22 ft. lbs. (22-30 Nm).
    8. Position the hose clamps between the alignment marks on both ends of the hose, then slide the hose on the connection. Tighten the hose clamps to 20-30 inch lbs. (2.2-3.4 Nm).
    9. Fill and bleed the cooling system.
    10. Connect the negative battery cable.
    11. Start the engine and check for leaks.

    Hope this help; good luck and remember rated this post.

    May 15, 2010 | 1995 Ford Windstar

    1 Answer

    Change the water pump. what size is the bolts


    Location, size and torque specification for the water pump bolts-3.0L OHV engine...

    f2d2658.jpg

    • Install the bolts in the water pump housing.
    • Tighten bolts Nos. 4, 5, 6, 7, 8, 9 and 10to 15-22 ft. lbs. (20-30 Nm). Tighten bolts Nos. 11, 12, 13, 14 and 15 to 71-106 inch lbs. (8-12 Nm).
      The bolts are of different lengths and must be installed in the correct locations.
    • If equipped, attach the engine control sensor wiring to the locating stud bolt.
    • Hand-tighten the water pump pulley retaining bolts.
    • Install the accessory drive belts.
    • Tighten the water pump pulley bolts to 15-22 ft. lbs. (20-30 Nm).
    • Connect the heater hose to the water pump.

    Hope this help (remember rated and comment this post).

    Apr 10, 2010 | 1999 Ford Taurus

    2 Answers

    Water pump needs replacing looking for the layout on the 92 lasebre engine, would make things a whole lot easier


    Loosen the bolts on the water pump pulley, then remove the belt, then remove the the 4 pulley bolts on the water pump. Then remove the water pump bolts, I think there's 6 bolts, size 8mm then remove the water pump.9b05c85.gif

    Mar 04, 2010 | 1992 Buick LeSabre

    3 Answers

    How do i remove pulley from water pump to put on new water pump...there is now bolt. very confused


    As I remember these cars, the water pump pulley was held on with three 10 mm bolts. If this is not the case, post a response with the engine size and code (8th digit of the VIN) and I'll try to help you.

    Nov 26, 2009 | 1992 Buick Century

    2 Answers

    How to replace a water pump on a 2002 chevrolet impala.is it easy to replace


    Right tools, patience, and patience.....

    Here is the procedures for the 3.5L engine (you didn't post your size):


    3.5L Engine
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Partially drain the cooling system.
    3. Remove or disconnect the following:
      • Surge tank outlet hose
      • Drive belt
      • Idler pulley
      • Water pump pulley

      NOTE The water pump is attached to the engine with both long and short bolts, be sure to note their locations.

      • Water pump
    fabbe65.gif
    Be sure to install the 5 long water pump bolts in the correct locations—3.5L engine

    d9d9244.gif
    Water pump mounting—3.5L engine

    To install:
    1. Install or connect the following:
      • Water pump using a new gasket and torque the bolts to 124 inch lbs. (14 Nm)
      • Water pump pulley and torque the bolts to 106 inch lbs. (12 Nm)
      • Idler pulley and torque the bolt to 37 ft. lbs. (50 Nm)
      • Drive belt
      • Surge tank hose
    2. Refill the cooling system.
    3. Start the engine and check for leaks.

    Oct 22, 2009 | 2002 Chevrolet Impala

    2 Answers

    Finding the water pump on 2001 chevy cavalier


    Need to know engine size but usually water pump is directly connected to the lower rad hose. Moe

    May 15, 2009 | 2001 Chevrolet Cavalier

    4 Answers

    Water pump removal on a 99 bonneville


    two bolts hold the power steering bracket on and come off easily. Then you can remove your bolt

    Apr 11, 2009 | 1999 Pontiac Bonneville

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    27 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cadillac Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8180 Answers

    Are you a Cadillac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...