Question about Cars & Trucks

1 Answer

96 dodge brake lights and hazard lights dont work

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

Check the fuse for the brake light circuit (its the same circuit for your hazard lights)

Posted on Jan 09, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: main brakes lights wont work

my brake lights do not work i have changed them and the fuse but do not work
1996 chevy silverodo

Posted on Oct 28, 2008

johnny5846
  • 379 Answers

SOURCE: 2001 dodge neon tail lights inop

looking at your schematics and , you say tail lights don't work , you didn't mention if front parking lights and license plate lights are working , they all come from the same source , a black /yellow wire , a good clue if front work and rear don't , please advise .if fronts work then you have a open circuit somewhere between junction S118 (near breakout for left headlamp) and rear sockets.

Posted on Dec 31, 2008

  • 114 Answers

SOURCE: Fix for no brake lights on Dodge Ram Van

Also if you work it on and off about 50 times it cleans the contacts up and will work ok also.

Posted on Mar 21, 2009

  • 335 Answers

SOURCE: All lights work on the rear except the three brake lights

Sounds like the brake light switch has a problem. Located above brake pedal and activated with the brake pedal arm. Check for power going in and coming out when you apply the brake.

Posted on May 24, 2009

abauto
  • 353 Answers

SOURCE: o2 Dodge Dakota Brake lights wont work but bulbs r good.

If the bulbs are good I would suspect the Brake light switch.

Brake Light Switch: Testing and Inspection
The brake lamp switch can be tested with an ohmmeter. The ohmmeter is used to check continuity between the pin terminals.
Switch Circuit Identification
- Terminals 1 and 2: brake lamp circuit
- Terminals 3 and 4: RWAL/ABS module and Powertrain Control Module (PCM) circuit
- Terminals 5 and 6: speed control circuit
Switch Continuity Test
NOTE: Disconnect switch harness before testing switch continuity.
With switch plunger extended, attach test leads to pins 1 and 2. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 3 and 4. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 5 and 6. Replace switch if meter indicates no continuity.


27c4c52.jpg

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hazards, blinkers and brake lights do not work.


all this is controlled by a fuse, i can't remember if it's in the dash by the driver door or under the hood

May 05, 2010 | 2001 Dodge Ram 3500 Truck

1 Answer

I have a 85 omni glh I blew my brake lights out I replaced the fuse but they still don't work , everything elae works on the car except the hazards , are the brake lights and the hazards connected...


yes they are. if your hazard flasher is bad and you happen to have the hazard switch turned on your brake lights wont work
put hazard switch in one position and check brake lights
then put in other position and check them
if they work with the hazard switch in one position leave switch olone and check fuses and put a new flasher for hazard in

Mar 24, 2010 | 1985 Dodge Omni

1 Answer

On a 2002 dodge ram 1500 truck the brake lights and the turn signals and winshield wipers dont work the only brake light that works is above the cab. and the turn signal flashes on the dash like they are...


I suspect a bad multi function switch located in the left hand side of the steering column. This switch controls your high/low beams/wiper delay/windshield washer/turn signals and hazards.

Dec 31, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

'96 ford Crown Victoria....No hazard or brake light no turn sigal


Sounds like the multifunction switch. Try working the hazard switch up and down a few times to see if you get some lights to work. If so then replace the switch.

Nov 09, 2009 | 1996 Ford Crown Victoria

1 Answer

All lights work on the rear except the three brake lights


Sounds like the brake light switch has a problem. Located above brake pedal and activated with the brake pedal arm. Check for power going in and coming out when you apply the brake.

May 24, 2009 | 1999 Dodge Durango

1 Answer

Fix for no brake lights on Dodge Ram Van


Also if you work it on and off about 50 times it cleans the contacts up and will work ok also.

Mar 05, 2009 | 1994 Dodge Ram

1 Answer

2001 dodge neon tail lights inop


looking at your schematics and , you say tail lights don't work , you didn't mention if front parking lights and license plate lights are working , they all come from the same source , a black /yellow wire , a good clue if front work and rear don't , please advise .if fronts work then you have a open circuit somewhere between junction S118 (near breakout for left headlamp) and rear sockets.

Dec 31, 2008 | 2001 Dodge Neon

3 Answers

No tail lights


you have a bad control module. the part number for it is 56051036af if you go to the dealer its about $238.

Nov 03, 2008 | 2002 Dodge Ram Maxi

1 Answer

My Dodge Caravan ST 3.4 LTR instrement cluster.


Your Hazard fuse is blown.
Hazard fuse has the instrument gauges on it in addition to the turn and brake lights.

When one of my brake lights went on my 07 Caravan it when short for a time and took out this fuse.

Oct 03, 2008 | 2007 Dodge Caravan SXT Minivan New Cars

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...