Question about 2008 Ford F-350 Super Duty

Open Question

How to remove 08 F350 drivers side air bag - 2008 Ford F-350 Super Duty

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
terseo
  • 92 Answers

SOURCE: disarm and remove ford expedition air bags

Remove the negative cable from your car battery before replacing car air bags

Deactivate the air bag by removing the air bag fuses. Look in your car owners manual to locate the fuses

Unscrew steering column paneling and remove the airbag bolts on the back side of the steering wheel. Pull out the airbag until you see the back side and unplug the wires

Posted on Sep 24, 2009

Ad
  • 4874 Answers

SOURCE: air bag light is and flashing code 27

This is a common fault on FORD
 
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.
 
 
Just push it together properly and it should clear the AirBag fault light 
 


Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 02 Lincoln Ls the airbag light flashes 3times and6 the code is 36 what is the diganose


Lamp Fault Code 36 has four possibilites, of which are the following:
-Driver Side Air Bag Circuit Shorted to Ground
-Driver Side Air Bag Circuit Shorted to Battery or Ignition
-Driver Side Air Bag Circuit Resistance High
-Driver Side Air Bag Circuit Resistance Low
With that said, it's most likely your driver air bag needs to be replaced
...

Apr 07, 2016 | Lincoln Cars & Trucks

1 Answer

How to remove the steering wheel for replacement


SIR DISABLE:
DRIVER SIDE
Many service procedures require the air bag system to be disabled to prevent accidental deployment. The air bag system can maintain sufficient voltage to cause deployment for up to 2 minutes after the ignition switch is turned off, the battery ground cable is disconnected or the DERM fuse is removed. If the inflator module is disconnected from the deployment loop by the following procedure, service can begin immediately without waiting for the 2 minute time period to elapse.
  1. Turn steering wheel so that vehicle wheels are pointed straight ahead.
  2. Turn ignition switch to Lock position and remove key.
  3. Remove air bag fuse from fuse block.
  4. Remove steering column filler panel.
  5. Remove Connector Position Assurance (CPA) and disconnect yellow two-way connector at base of steering column, Fig. 1.
PASSENGER SIDE
  1. Remove air bag fuse from fuse block.
SIR ENABLE:
Driver Side
  1. Turn ignition switch to LOCK and remove key.
  2. Connect yellow two-way connector and install connector position assurance (CPA).
  3. Install steering column filler panel.
  4. Insert air bag fuse into fuse block.
  5. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.
Passenger Side
  1. Turn ignition switch to LOCK and remove key.
  2. Insert air bag fuse into fuse block.
  3. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.

remove-steering-wheel-replacement-rfvykuizssn2qn2mhtsbw2yl-3-0.png

Apr 10, 2015 | 1996 Chevrolet K1500

2 Answers

Air bag code B1378 2008 chevy aveo


You could clear the code with a scanner, but its possible the sensor for the driver side bag is faulty.

Jun 29, 2013 | Cars & Trucks

2 Answers

Steering wheel adjustment , the steering whell is 90degrees off but the car does not pull eather direction. car was stolen no damage just steering whell truned


jack front of car up then turn steering wheel full lock to full lock and count the number of turns from either side then divide by 2 so you have the straight ahead position then remove the steering wheel and replace in the straight ahead position ,iam saying this because the vehicle may have been re tracked and only one track rod end adjusted so you have say 2 turns to the left and 2 and half to the right if you follow me .or remove the steering wheel then just hold it on and slowly drive forewards and lift wheel and refit to the correct position

Feb 10, 2011 | 1999 Mercury Grand Marquis

1 Answer

Need to remove heater A/C dash control , what is proper procedure?


Look at fig. 4 for the heater a/c dash control: HEATER CORE Altima REMOVAL AND INSTALLATION
  1. Position the steering wheel in the straight-ahead position.
  2. Turn the ignition switch OFF.
  3. Disconnect the negative (() battery cable; then, the positive (+) battery cable. NOTE: Wait for a least 3 minutes after disconnecting the battery cables for the charge in the air bag circuit to dissipate before working on the air bag module(s).
  4. Remove the driver's side SRS and steering wheel by removing or disconnecting the following:
    • Lower lid from the steering wheel and disconnect the driver's air bag module connector
    • Left and right side lids from the steering wheel
    • Special bolts from both side of the steering wheel using a tamper resistant Torx wrench (T50)
    • Air bag module and store it face up
    • Horn's electrical connector and remove the steering wheel nut
    • Steering wheel from the steering column using a suitable puller
  5. Remove the passenger's side SRS by removing or disconnecting the following:
    • Glove box door and the glove box
    • Front passenger's air bag module connector
    • 2 special bolts using a tamper resistant Torx wrench (T50)
    • 4 passenger's air bag-to-instrument panel nuts
    • Front passenger's air bag module and store it face up.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
  8. Working in the engine compartment, disconnect the heater hoses from the heater core tubes.
  9. Remove the instrument panel by removing or disconnecting the following:
    • Kick plate and dash side finisher on the driver's side
    • 2 lower panel-to-instrument panel screws and the lower panel on the driver's side
    • 2 lower reinforcement panel-to-instrument panel screws and the lower reinforcement panel
    • 6 steering column cover screws, the covers, the spiral cable and combination switch
    • 2 cluster lid "A" screws and the cluster lid "A"
    • 3 combination meter screws, disconnect the electrical harness connector and remove the combination meter
    • Switch panel
    • Instrument panel lower covers
    • Snap out the transmission shifter finisher (boot)
    • 4 cluster lid "C" screws and the cluster lid "C"
    • 4 audio and deck pocket-to-instrument panel screws and the audio and deck pocket
    • 5 center console screws and the center console
    • 2 center instrument panel screws and the center panel
    • front defroster grilles
    • Front pillar garnish
    • Instrument panel 3 nuts/4 screws and the instrument panel
    • 8 instrument stay assembly nuts and the stay
    • Steering member assembly 5 nuts/1 bolt and the steering member
  10. Remove the air conditioning housing assembly by removing or disconnecting the following:
    • Refrigerant lines from the air conditioning housing assembly
    • Thermo control amp
    • Air conditioning housing assembly
  11. Remove or disconnect the following:
    • Heater unit
    • Heater core from the heater unit Fig. 1: Exploded view of the steering wheel and air bag module 93112gd9.gif
      Fig. 2: Exploded view of the passenger's side air bag module 93112gd0.gif
      Fig. 3: Exploded view of the instrument panel assembly 93112ge1.gif
      Fig. 4: Exploded view of the heater housing assembly and related components 93112ge2.gif
      Fig. 5: View of the heater core and heater housing 93112ge3.gif
    To install:
  12. Install or connect the following:
    • Heater core to the heater unit
    • Heater unit
  13. Install the air conditioning housing assembly by installing or connecting the following:
    • Air conditioning housing assembly
    • Thermo control amp
    • Refrigerant lines to the air conditioning housing assembly
  14. Install the instrument panel by installing or connecting the following:
    • Steering member assembly and the steering member 5 nuts/1 bolt
    • Instrument stay assembly and the 8 stay nuts
    • Instrument panel and the instrument panel 3 nuts/4 screws
    • Front pillar garnish
    • Front defroster grilles
    • Center instrument panel and the 2 center panel screws
    • Center console and the 5 center console screws
    • Audio and deck pocket and the 4 audio and deck pocket-to-instrument panel screws
    • Cluster lid "C" and the 4 cluster lid "C" screws
    • Snap in the transmission shifter finisher (boot)
    • Instrument panel lower covers
    • Switch panel
    • Combination meter, connect the electrical harness connector and install the 3 combination meter screws
    • Cluster lid "A" and the 2 cluster lid "A" screw
    • Combination switch, the spiral cable, the covers and the 6 steering column cover screws
    • Lower reinforcement panel and the 2 lower reinforcement panel-to-instrument panel screws
    • Lower panel and the 2 lower panel-to-instrument panel screws, on the driver's side
    • Kick plate and dash side finisher, on the driver's side
  15. Working in the engine compartment, connect the heater hoses to the heater core tubes.
  16. Install the passenger's side SRS by installing or connecting the following:
    • Front passenger's air bag module
    • 4 passenger's air bag-to-instrument panel nuts
    • 2 new special bolts and torque using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm)
    • Front passenger's air bag module connector
    • Glove box door and the glove box
  17. Install the driver's side SRS and steering wheel by installing or connecting the following:
    • Steering wheel to the steering column
    • Steering wheel nut and torque the nut to 22-29 ft. lbs.
    • Horn's electrical connector
    • Air bag module
    • New special bolts to both sides of the steering wheel and torque the bolts using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm).
    • Both the left and right side lids to the steering wheel
    • Lower lid to the steering wheel and connect the driver's air bag module connector
  18. Refill the cooling system.
  19. Connect the positive (+) battery cable; then, the negative (() battery cable.
  20. Evacuate, charge and leak test the air conditioning system refrigerant.
  21. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Nov 19, 2010 | 2002 Nissan Sentra

1 Answer

Replaceing driver side air bag


First things first, remove your negative battery cable off the battery and wait ten minutes to discharge the drivers airbag squid, look behind , and the sides of the steering wheel, you will see 2 screws, one on each side, remove them, than the air bag assembly will lift off, there is wires attached to it, just unplug them and its out of there, reverse the procedure, and install your neg cable back on, you should be good to go. while the cable was off the acm cleared its self of codes, when the keys is turn on the system will do a selt test, and air bag light shoud go out. GOOD LUCK, RDJRP

Oct 01, 2009 | 1994 Dodge Ram

1 Answer

Disarm and remove ford expedition air bags


Remove the negative cable from your car battery before replacing car air bags

Deactivate the air bag by removing the air bag fuses. Look in your car owners manual to locate the fuses

Unscrew steering column paneling and remove the airbag bolts on the back side of the steering wheel. Pull out the airbag until you see the back side and unplug the wires

Sep 24, 2009 | 2003 Ford Expedition

1 Answer

How do i remove the air bag on my 2005 vw bettle?


TURN IGNITION SWITCH OFF.MAKE SURE RADIO IS OFF SO YOU WONT LOSE CODE.DISCONNECT NEGATIVE BATTERY CABLE.WAIT AT LEAST 10 MINUTES BEFORE REMOVING AIR BAG.LET THE AIR BAG BATTERY BACK UP POWER. DISCHARGE.BECAREFUL HANDLING AIR BAG. DONT CARRY IT BY IT WIRES.WHEN CARRYING IT.HOLD IN BOTH HANDS SECURLY.WHEN LAYING IT DOWN .BESURE THE BAG AND TRIM COVER FACING UP.BESURE TO KEEP KIDS AND PETS AWAY. BECAUSE AIR BAG CAN STILL BE DEPLOYED.SO BE CAREFUL.

Jun 16, 2009 | 2005 Volkswagen New Beetle Convertible

1 Answer

Airbag deployed


SECTION 501-20B: Occupant Restraints — Passive — Supplemental Air Bag System 2000 Villager Workshop Manual REMOVAL AND INSTALLATION Module —Driver Air Bag Removal
syv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The backup power supply energy must be depleted before any air bag component service is performed. To deplete the backup power supply energy, disconnect the battery ground cable and wait three minutes.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again. If the vehicle was in a frontal collision and the air bag did not deploy, the air bag may not have been needed. Complete a diagnosis of the air bag system before installing a new driver side air bag module (043B13). Refer to Diagnosis and Testing in this section.
  1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
  1. Remove the two driver air bag module retaining bolt access covers (one shown).
  1. Remove the steering wheel bottom cover to access the driver air bag module electrical connector.
  1. Disconnect the driver air bag module electrical connector.
  1. syv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: After removing, discard the driver side air bag module bolts and install new driver air bag module bolts during installation.
    Remove the two driver air bag module retaining bolts (one shown) and discard.
  1. Remove the driver air bag module.
    1. Separate the driver air bag module from the steering wheel and disconnect the horn pad switch.
    1. Remove the driver air bag module.

Apr 16, 2009 | 2000 Nissan Quest

1 Answer

Air bag code


I strongly suspect you have a bad connection or corroded connection at one of your connectors.

Here's the LFC (lamp Fault Codes) for 36:

B1993 36 22 Driver Side Air Bag Circuit Shorted to Ground GO to Pinpoint Test V . B1992 36 24 Driver Side Air Bag Circuit Shorted to Battery or Ignition GO to Pinpoint Test W . B1994 36 26 Driver Side Air Bag Circuit Resistance High GO to Pinpoint Test X . B1995 36 28 Driver Side Air Bag Circuit Resistance Low GO to Pinpoint Test Y .


eea36a4.gif

Feb 18, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
2008 Ford F-350 Super Duty Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...