Question about 1999 Honda Civic

Open Question

Honda Thermostat housing torque specs

Thermostat Housing

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 449 Answers

SOURCE: Where & how to install thermostat in honda accord ex 1992

you need to follow the upper hose that lead from the radiator to the engine, there is two bolt that connect the thermostat housing to the block loosen the bolt using a 10 mm socket with ra-chet. Make sure that the engine is cool off before attempt to do this you will lose coolant but that's ok you will add the coolant when you finish replacing the thermostat. start the engine with the radiator cap off then add coolant slowly and cap it, then fill the reservoir up.

note the way you remove the thermostat that's the same way you will put the new one so pay attention when you remove the old one good luck.

Posted on Dec 17, 2008

Ad
  • 1 Answer

SOURCE: Replacing head gasket on 1995 honda civic, require torque specs and secquence

wow. a lot of bad information on this site. Refer to a manual for the proper torque sequence. The civic I believe is a two step torque procedure. First 22 ft lbs, than 53 ft lbs.

Posted on Jan 01, 2009

SOURCE: Torque specs for 96 Honda Accord 2.2L

the main bearings bolts is to 1st step 30Nm or 22lbs ft and the last step is 75Nm or 54lbs ft in this tighten secuence. 9 3 1 5 7 on the top bolts and........ ........ ........ ... 8 6 2 4 10 botton bolts and the connecting rod 45Nm or 34 lbs ft i hope be help you

Posted on Nov 09, 2009

  • 12 Answers

SOURCE: head bolt torque specs for 200 honda accord 3.0

its a three step process 1st 29ft/lbs 2nd 51ft/lbs 3rd 72.3ft/lbs

Posted on Apr 25, 2010

SOURCE: Thermostat housing diagram 1992 Honda civic

Follow the top radiator hose to the engine and where it hooks up is your housing. No diagram needed.

Posted on Jan 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for 01 Honda Civic 1.6L VTEC to include intake , exhaust, thermostat housing to head cam pully


try referring to the repair manual. usually always has torque specifications:
http://www.papertownspdf.com/downloads/honda-civic-repair-manual-2000-2005/

Dec 30, 2016 | Honda Cars & Trucks

2 Answers

1995 ford windstar thermostat housing bolt torque spec


Most people don't bother using a torque wrench to tighten a thermostat housing.

It is more important to be careful and tighten each bolt a little at a time. You do not want to warp, crack, miss align the part you are bolting.

It does not take a lot of torque to seal a thermostat housing. I would guess somewhere between 15 and 20 ft lbs.

It is often hard to find such torque specs for specific vehicles.

For bolts that you cannot find a specified torque spec, you can refer to a standard bolt torque chart. The charts are based on the diameter of the bolt threads not the wrench size used to fit the bolt head. The charts also depend on the hardness of the bolt material. Also keep in mind the material you are bolting into.

Here is one such chart...
http://www.dansmc.com/torque_chart.htm

Keep in mind that thermostat housing bolts are just sealing a gasket. They are not holding the entire car together.

After turning wrenches for many years, most mechanics just know by feel.

There are cases where a torque wrench is mandatory. Like head bolts, wheel bearing/hub nuts, rod caps, main bearing, etc.

Jul 16, 2014 | Ford Windstar Cars & Trucks

1 Answer

Replace termastat 97 tracker 4 cylinder


follow the upper radiator hose to the piece on the engine where it connects. this is the thermostat housing. remove the housing clean both surfaces replace the thermostat making sure to orient the thermostat the same way as the original. install gasket using water rated gasket seal and torque the bolts to specs. let set for several hours, refill radiator, and presto

Jul 04, 2014 | Cars & Trucks

1 Answer

What are the torque specs for a 2003 Chevrolet trailblazer thermostat housing?


The 2003 Chevrolet Vortec 5300 generated 285 horsepower at 5,200 rpm and 325 ft.-lbs. of torque at 4,000 rpm. --------------------------------------------------------------
VVDI VAG Vehicle Diagnostic

Mar 26, 2013 | Cars & Trucks

1 Answer

Location of engine thermostat


Removal & Installation 3.0L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section
  2. Drain the engine cooling system
  3. Remove or disconnect the following:
    • Air cleaner outlet tube
    • Hoses and remove the thermostat housing assembly
    • Bolts separate the housing and remove the thermostat and seal
To Install:
  1. Install or connect the following:
    • New seal and thermostat. Torque bolts to 8 ft-lbs (11 Nm)
    • Hoses to assembly
    • Air cleaner outlet tube
3.9L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section
  2. Drain the engine cooling system
  3. Remove or disconnect the following:
    • Intake manifold
    • Nuts and remove the hose bracket
    • Stud bolts
    • Lower radiator hose from the thermostat housing
    • Bolts and thermostat housing cover
    • Thermostat and seal
To Install:
  1. Install or connect the following:
    • New seal and thermostat
    • Housing cover. Torque bolts to 8 ft-lbs (11 Nm)
    • Lower radiator hose to the thermostat housing
    • Stud bolts. Torque to 10 ft-lbs (13 Nm)
    • Hose bracket. Torque nuts to 89 in-lbs (10 Nm)
    • Intake manifold

Aug 17, 2010 | 2000 Lincoln LS

1 Answer

What is the torque spec for the thermostat housing


THERMOSTAT HOUSING BOLT TORQUE IS 15 - 22 FT LBS.

Jul 11, 2010 | 1998 Lincoln Town Car

1 Answer

How to replace 2003 xj8 thermostat, car is over heating and fan runs when turned off


=thermostats are easy fixes, just locate your upper radiator hose and where it enters the engine. three should be a thermostat housing at the end of the hose and it will be bolted to the engine. Remove this housing and replace with correct thermostat and gasket and tighten housing to the proper torque specs. You will need to use care when removing the bolts as it appears to have some clerance problems on some of the housing bolts as it is bolted to composite plastic material and is easily damaged. here is link. I would not over tighten the bolts again because of the material.

http://jaguarforums.com/forum/archive/index.php/t-5621.html

Oct 27, 2009 | Jaguar Xj Series Cars & Trucks

1 Answer

What is torque spec for 2004 Ford 4.0 thermostat cover bolts? Replaced black ''plastic'' thermostat housing and inlet cover. Thanks


Normally these bolts are about 20-24ft lbs. You don't want to over tighten them as they should have a rubber washer/gasket to help provide a good seal. These cast aluminum housing will easily strip so just use care when tightening. Just snug both bolts and run the vehicle til it reaches operating temp then check for leaks. You can also purchase a Chiltons/Haynes manual for your vehicle at any auto parts store for $15 they normally give you the torque specs as well as some other valuable tipe

Aug 06, 2009 | 2004 Mercury Mountaineer

1 Answer

Torque specs


Hello mikemcgee63, my name is JShreader. Thank you for choosing fixya.com.

The Torque Specs for the Thermostat Housing are 10 Nm (89 inch lbs.).

I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Mar 30, 2009 | 2001 Chevrolet Corvette

Not finding what you are looking for?
1999 Honda Civic Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...